- 您現在的位置：買賣IC網 > PDF目錄98062 > PT5827A (TEXAS INSTRUMENTS INC) 16 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, SMA18 PDF資料下載
參數資料
| 型號： | PT5827A |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 16 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, SMA18 |
| 封裝： | HORIZONTAL MOUNT PACKAGE-18 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 207K |
| 代理商： | PT5827A |
Application Notes
For technical support and more information, see inside back cover or visit www.ti.com
PT5820 Series
Adjusting the Output Voltage of the
PT5820 Series of Step-Down ISRs
Using Margin Up/ Margin Down
The Margin Up (pin 4) and Margin Down (pin 3) control
inputs allow the output voltage to be easily adjusted by
approximately ±5% of the the set-point voltage. These
control inputs provide a convenient method for applying
a momentary adjustment to test a load circuit’s supply
voltage margins. To activate, simply connect the appro-
priate control input to the Sense(–) (pin 8), or the local
starpoint ground. Either a logic level MOSFET or a
p-channel JFET is recommended for this application.
Using the ‘V
o
Adjust’ Control
For a more permanent and precise adjustment, use the
Vo Adjust control (pin 1). The Vo Adjust control allows
adjustment in any increment by up to ±10% of the set-
point. The adjustment method requires the addition of a
single external resistor. Table 3-1 gives the allowable
adjustment range for each model of the series as Va (min)
and Va (max). The value of the external resistor can either
be calculated using the formulas given below, or simply
selected from the range of values provided in Table 3-2.
Refer to Figure 3-1 for the placement of the required
resistor. Use the resistor R1 to adjust up, and the resistor
(R2) to down.
Adjust Up: An increase in the output voltage is obtained
by adding a resistor R1, between Vo Adjust (pin 1) and
Sense(–) (pin 8). See Figure 3-1.
Adjust Down: Add a resistor (R2), between Vo Adjust (pin 1)
and Sense(+) (pin 18). See Figure 3-1.
Figure 3-1; V
o
Adjust Resistor Placement
Vo Adjust Resistor Calculations
The values of R1 [adjust up] and (R2) [adjust down] can
also be calculated using the following formulas. Again, use
Figure 3-1for the placement of the required resistor;
either R1 or (R2) as appropriate.
R1
=
Vr Ro
– 24.9
k
Va – Vo
(R2)
=
Ro (Va – Vr)
– 24.9
k
Vo – Va
Where: Vo = Original output voltage
Va = Adjusted output voltage
Vr = The reference voltage in Table 3-1
Ro = The resistance constant in Table 3-1
Table 3-1
ISR OUTPUT VOLTAGE ADJUSTMENT RANGE AND FORMULA PARAMETERS
Series Pt. No.
PT5827
PT5821
PT5822
PT5823
PT5824
PT5825
PT5826
Vo (nom)
5.0V
3.3V
2.5V
1.8V
1.5V
1.2V
1.0V
Va (min)
4.0V
2.6V
2.0V
1.52V
1.31V
1.1V
0.94V
Va (max)
5.5V
3.63V
2.8V
2.1V
1.82V
1.52V
1.32V
Vr
1.27V
0.8V
Ro (k
)
10.0
10.2
10.7
10.2
9.76
10.0
10.2
Notes:
1. Use a 1% (or better) tolerance resistor in either the R1 or
(R2) location. Place the resistor as close to the ISR as
possible.
2. Never connect capacitors from Vo Adjust to either GND or
Vout. Any capacitance added to the Vo Adjust pin will affect
the stability of the ISR.
3. If the remote sense feature is not being used, the adjust
resistor (R2) can be connected to Vout, (pins 14-17) instead
of Sense (+).
PT5820
9–13
1
18
14–17
8
C
OUT
330F
(Optional)
+
GND
V
OUT
Sense (+) [Note 3]
Sense (–)
(R
2)
Adj Down
V
O Adj
GND
Sense(+)
Sense(–)
V
OUT
R
1
Adjust Up
相關PDF資料 |
PDF描述 |
|---|---|
| PT5821C | 16 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, SMA18 |
| PT5824N | 16 A SWITCHING REGULATOR, 400 kHz SWITCHING FREQ-MAX, SMA18 |
| PT6121R | 1 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDFM12 |
| PT6122B | 1 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDFM12 |
| PT6121B | 1 A SWITCHING REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDFM12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT5827C | 功能描述:DC/DC轉換器 5V 16A 12-V Input Adj Step-Down ISR RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| PT5827N | 功能描述:開關變換器、穩壓器與控制器 5V 16A 12-V Input Adj Step-Down ISR RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| PT583SMFBN | 功能描述:CBL ASSY RG58U SMBM BNCM RoHS:是 類別:電纜組件 >> 同軸，RF 系列:* 標準包裝:1 系列:- 類型:母型至公型 樣式:BNC 至 N 型 第一連接器:BNC 公插頭 第二連接器:N 母插孔 長度:- 纜線類型:- 阻抗:- 頻率 - 最大:- 顏色:- 特點:- 工作溫度:- 其它名稱:RAD-CON-N-BNC-BS |
| PT-593SQ | 功能描述:Peak-Peak Signal Buzzer Single Tone 3.5kHz Piezo 5 ~ 150V 90dB @ 5V, 30cm 制造商:mallory sonalert products inc. 系列:PT 包裝:散裝 零件狀態:有效 驅動器電路:傳感器，外部驅動 輸入類型:峰-峰信號 電壓 - 額定:5V 電壓范圍:5 ~ 150V 頻率:3.5kHz 技術:壓電 工作模式:單音調 持續時間:- 聲壓級:90dB @ 5V，30cm 電流 - 電源:4mA 端口位置:頂部 工作溫度:-20°C ~ 70°C 認可:- 等級:- 安裝類型:表面貼裝 端接:焊盤 大小/尺寸:54.5mm 直徑 x 23.7mm 高 高度 - 安裝（最大值）:* 標準包裝:1 |
| PT5F21E-KE | 制造商:TE Connectivity 功能描述:Power Tool Switches |
發布緊急采購，3分鐘左右您將得到回復。