參數資料
型號： PT4701A
廠商： TEXAS INSTRUMENTS INC
元件分類： 電源模塊
英文描述： 4-OUTPUT 35 W DC-DC REG PWR SUPPLY MODULE
封裝： METAL, SIP-15/21
文件頁數： 4/11頁
文件大?。?/td> 206K
代理商： PT4701A
For technical support and more information, see inside back cover or visit www.ti.com
Pin Function
1+Vin
2–Vin
3
EN 2
4
EN 1
5
Do Not Connect
6
Do Not Connect
7
Do Not Connect
PT4701—48V
35-W Quad-Output
DC/DC Converter for DSL
On/Off Enable Logic
Pin Descriptions
Pin 3
Pin 4
Output Status
×1
Off
10
On
0×
Off
Notes:
Logic 1 =Open collector
Logic 0 = –Vin (pin 2) potential
For positive Enable function, connect pin 4
to pin 2 and use pin 3.
For negative Enable function, leave pin 3
open and use pin 4.
+Vin:
The positive input supply for the module with
respect to –Vin. When powering the module from a
–48V telecom central office supply, this input is
connected to the primary system ground.
–Vin:
The negative input supply for the module, and
the 0VDC reference for the EN 1, and EN 2 inputs.
When powering the module from a +48-V supply,
this input is connected to the 48-V(Return).
EN 1:
The negative logic input that activates the
module output. This pin must be connected to –Vin
to enable the module’s outputs. A high impedance
disables the module’s outputs.
EN 2:
The positive logic input that activates the
module output. If not used, this pin should be left
open circuit. Connecting this input to –Vin disables
the module’s outputs.
+Vo 1:
This is the positive high-output voltage. It is
the balanced compliment of (–Vo1) and referenced
to the secondary COM node.
–Vo 1:
The negative high-output voltage, which is the
balanced compliment of (+Vo1) with respect to COM.
+Vo 2:
This is the positive low-output voltage. It is
the balanced complement of (–Vo2) and referenced
to the secondary COM node.
–Vo 2:
The negative low-output voltage, which is the
balanced compliment of (+Vo2) with respect to COM.
COM:
This is the common node and the secondary
reference for all four regulated output voltages. It
provides a return for any unbalanced load current,
and is DC isolated from the input supply pins.
±Vo1 Adjust:
Using a single resistor, this pin allows
the simultaneous adjustment of both +Vo1 and -Vo1
magnitude with respect to the COM node. Adjust-
ment can be higher or lower than the preset value.
If not used this pin should be left open circuit.
±Vo2 Adjust:
Using a single resistor, this pin allows
the simultaneous adjustment of both +Vo2 and -Vo2
magnitudes with respect to the COM node. Adjust-
ment can be higher or lower than the preset value.
If not used this pin should be left open circuit.
Environmental Specifications
Characteristics
Symbols
Conditions
Min
Typ
Max
Units
Operating Temperature Range
Ta
Over Vin Range
–40
—
85 (i)
°C
Solder Reflow Temperature
Treflow
Surface temperature of module pins or case
—
215 (ii)
°C
Storage Temperature
Ts
—
–40
—
125
°C
Mechanical Shock
Per Mil-STD-883D, Method 2002.3
—
500
—
G’s
1 msec, Sine, mounted
Mechanical Vibration
Mil-STD-883D, Method 2007.2
Suffix A
—
15 (iii)
—
G’s
20-2000 Hz
Suffix N, C
—
20 (iii)
—
Weight
—
Vertical/Horizontal
—
50
—
grams
ShutdownTemperature
OTP
115
125
°C
Flammability
—
Meets UL 94V-O
Notes:
(i) See SOA curves or consult factory for appropriate derating.
(ii) During solder reflow of SMD package version, do not elevate the module case, pins, or internal component temperatures above a peak of 215 °C. For
further guidance refer to the application note, “Reflow Soldering Requirements for Plug-in Power Surface Mount Products,” (SLTA051).
(iii) Only the case pins on through-hole pin configurations (N & A) must be soldered. For more information see the applicable package outline drawing.
Pin Function
8
Pin Not Present
9
Pin Not Present
10
Pin Not Present
11
Pin Not Present
12
Pin Not Present
13
Pin Not Present
14
+Vo1
Pin Configuration
Note: Shaded functions indicates those pins that are at primary-side
potential. All other pins are referenced to the secondary.
Pin Function
15
COM
16
–Vo1
17
±Vo1 Adjust
18
+Vo2
19
COM
20
–Vo2
21
±Vo2 Adjust
SLTS182A - FEBRUARY 2003 - REVISED APRIL 2003
相關PDF資料
PDF描述
PT4841C 3-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE
PT4842N 3-OUTPUT 62 W DC-DC REG PWR SUPPLY MODULE
PT4842C 3-OUTPUT 62 W DC-DC REG PWR SUPPLY MODULE
PT4841A 3-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE
PT4842A 3-OUTPUT 62 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
PT4701C 功能描述:直流/直流開關轉換器 35W Quad-Outp 48V Inpt DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
PT4701N 功能描述:直流/直流開關轉換器 35W Quad-Outp 48V Inpt DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT
PT4711 制造商:TI 制造商全稱:Texas Instruments 功能描述:45-W Dual-Output Isolated DC/DC Converter
PT4711A 功能描述:DC/DC轉換器 45W Dual 15V Out 48V Inpt Iso DC/DC Cnvtr RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
PT4711C 功能描述:DC/DC轉換器 45W Dual 15V Out 48V Inpt Iso DC/DC Cnvtr RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*