- 您現在的位置：買賣IC網 > PDF目錄370024 > PT4701 150V Single N-Channel HEXFET Power MOSFET in a SO-8 package; A IRF7451 with Standard Packaging PDF資料下載
參數資料
| 型號： | PT4701 |
| 英文描述： | 150V Single N-Channel HEXFET Power MOSFET in a SO-8 package; A IRF7451 with Standard Packaging |
| 中文描述： | 35鎢四路輸出。 48 - V輸入直流/直流轉換器的DSL線路驅動器 |
| 文件頁數： | 6/13頁 |
| 文件大?。?/td> | 345K |
| 代理商： | PT4701 |
For technical support and more information, see inside back cover or visit www.ti.com
PT4701
Operating Features of the PT4701 Quad-Output
DC/DC Converter for DSL Line Drivers
Balanced Load Fault Protection
A balanced load fault is the result of excess current flowing
from one +V
o
output directly to the corresponding –V
o
output. The current flowing in or out of the COM node
(pins 15 & 19) under this condition is within normal
operating limits. Both (±)dual outputs from the PT4701
DC/DC converter incorporate protection against this
type of load fault. This includes an absolute current limit
in combination with a fault timeout period. When the
balanced fault current from either ±dual output exceeds
the “Balanced Load Current Limit Threshold” (see data
sheet specifications), the converter initially limits the
fault current to approximately 150 % of the maximum
output current rating. If the fault persists for more than
20 ms the converter shuts down, forcing the voltage at
all four regulated outputs to simultaneously fall to zero.
Following shutdown the converter will periodically
attempt to recover by executing a soft-start power-up.
The converter will continually cycle through successive
over-current shutdowns and restarts until the fault is
removed.
Imbalanced Load Fault Protection
An imbalanced load fault is the result of excess current
flowing between any one of the +V
o
(or the –V
o
) outputs,
and the COM node (pins 15 & 19). When the current
sensed in the COM node exceeds the “Unbalanced Load
Shutdown Threshold” (see data sheet specifications), the
PT4701 shuts down and latches off within 1ms. Once
latched off, the module must be reset by momentarily
interrupting the input power source.
Over-Temperature Protection
The PT4701 DC/DC converter has an internal tem-
perature sensor, which monitors the temperature of the
module’s internal components. If the sensed temperature
exceeds a nominal 115 °C, the converter will shut down.
The converter will automatically restart when the sensed
temperature returns to about 100 °C.
Under-Voltage Lock-Out
The Under-Voltage Lock-Out (UVLO) circuit prevents
operation of the converter whenever the input voltage to
the module is insufficient to maintain output regulation.
The UVLO has approximately 2 V of hysterisis. This is
to prevent oscillation with a slowly changing input volt-
age. Below the UVLO threshold the module is off and
the enable control inputs, EN1 and EN2 are inoperative.
Primary-Secondary Isolation
The PT4701 DC/DC converter incorporates electrical
isolation between the input terminals (primary) and the
output terminals (secondary). All converters are production
tested to a withstand voltage of 1500 VDC. The isolation
complies with UL60950 and EN60950, and the require-
ments for operational isolation. This allows the converter
to be configured for either a positive or negative input
voltage source.
The regulation control circuitry for these modules is
located on the secondary (output) side of the isolation
barrier. Control signals are passed between the primary
and secondary sides of the converter. The data sheet ‘Pin
Descriptions’ and ‘Pin-Out Information’ provides guid-
ance as to which reference (primary or secondary) that
must be used for each of the external control signals.
Input Current Limiting
The converter is not internally fused.
For safety and
overall system protection, the maximum input current to
the converter must be limited. Active or passive current
limiting can be used. Passive current limiting can be a
fast acting fuse. A 125-V fuse, rated no more than 5 A, is
recommended. Active current limiting can be imple-
mented with a current limited “Hot-Swap” controller.
Application Notes
相關PDF資料 |
PDF描述 |
|---|---|
| PT4801 | 150V Single N-Channel HEXFET Power MOSFET in a D-Pak package; A IRFR13N15D with Tape and Reel Packaging |
| PT480 | Narrow Acceptance Phototransistor |
| PT480F | Narrow Acceptance Phototransistor |
| PT4841 | 15V/3.3V/1.5V 48V-Input 65 Watt Triple-Output DC/DC Converter |
| PT4841A | 100V Single N-Channel HEXFET Power MOSFET in a TO-220 FullPak (Iso) package; Similar to IRLI520N with Lead Free Packaging |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PT4701A | 功能描述:直流/直流開關轉換器 35W Quad-Outp 48V Inpt DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PT4701C | 功能描述:直流/直流開關轉換器 35W Quad-Outp 48V Inpt DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PT4701N | 功能描述:直流/直流開關轉換器 35W Quad-Outp 48V Inpt DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| PT4711 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:45-W Dual-Output Isolated DC/DC Converter |
| PT4711A | 功能描述:DC/DC轉換器 45W Dual 15V Out 48V Inpt Iso DC/DC Cnvtr RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
發布緊急采購，3分鐘左右您將得到回復。