- 您現在的位置：買賣IC網 > PDF目錄385752 > PST621 (MITSUMI ELECTRIC) System Reset (with battery back-up) Monolithic IC PDF資料下載
參數資料
| 型號： | PST621 |
| 廠商： | MITSUMI ELECTRIC |
| 英文描述： | System Reset (with battery back-up) Monolithic IC |
| 中文描述： | 系統復位（帶電池備份）單片集成電路 |
| 文件頁數： | 6/6頁 |
| 文件大?。?/td> | 193K |
| 代理商： | PST621 |
MITSUMI
System Reset (with battery back-up) PST620, 621
1. Connection
1. +5V power supply to V
CC
1 (Pin 2).
2. Connect back-up capacitor to V
CC
2 (Pin 3).
3. Connect a diode between V
CC
1 (Pin 2) and V
CC
2 (Pin 3).
4. Connect pulse width setting resistor and capacitor to PC (Pin 4) when using pulse shaver.
5. RE output (Pin 5) is reset signal output and is output when V
CC
is less than 2.15V.
6. When using pulse shaver, P
SCONT
(Pin 6) is high level.
7. CE output (Pin 7) is for chip enable signal and goes low when power outage is detected.
2. Theory of Operation
1. When +5V power is supplied normally, it is charged to the back-up capacitor via a diode.
2. The back-up capacitor starts back-up if +5V power supply voltage drops for some reason and
V
CC
1 goes below 4.2V, and at the same time the CE
standby mode, so that it operates on low current consumption.
3. When +5V power supply recovers and goes over 4.2V, an RE output signal of a certain width is
output, and this signal resets the 1-chip microcomputer. At the same time normal mode starts and
the time until crystal oscillator output stabilizes is reset.
4. If +5V power supply does not recover, and back-up capacitor voltage goes below 2.15V, reset is
carried out by the RE output signal to prevent the microcomputer from running wild.
3. Setting AC power supply power outage detection
1. Theory of operation for detecting AC voltage
AC voltage is rectified and smoothed by the capacitor. This voltage is divided and set at VAC input
detection voltage, +2V. At this time the smoothing capacitor and dividing resistor time constants
are used to set AC voltage missing waveform.
2. VAC voltage setting (R1, R2)
Set resistor ratio at the midpoint between R1 and R2 so that the voltage to be detected is +2V.
Impressed AC voltage
There is are no limitations on AC voltage as it is divided by R1 and R2 and applied to PST620.
3. Setting time constants to detect AC voltage (C4, R1+R2)
For impressed AC voltage of 5Vrms, and C4 and R1+R2 time constant of 60mS, set so that AC
voltage detects power outage when approximately 2 waveforms are missed. The time constants
can be set to detect missing AC waveforms.
signal switches the 1-chip microcomputer to
Application Circuits
VAC input : Stable power supply primary voltage detection
相關PDF資料 |
PDF描述 |
|---|---|
| PST623 | System Reset |
| PST7029 | System Reset Monolithic IC PST70XX Series |
| PST7019 | System Reset Monolithic IC PST70XX Series |
| PST7020 | System Reset Monolithic IC PST70XX Series |
| PST7021 | System Reset Monolithic IC PST70XX Series |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PST623 | 制造商:MITSUMI 制造商全稱:Mitsumi Electronics, Corp. 功能描述:System Reset |
| PST623XS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage Detector |
| PST623XW | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage Detector |
| PST-7 | 制造商:Panduit Corp 功能描述: |
| PST-7-01 | 功能描述:PUSH SPACER TEARDROP NAT 7/16" RoHS:是 類別:硬件，緊固件，配件 >> 電路板支座 系列:PST 標準包裝:1,000 系列:REHCBS 保持類型:卡入式鎖定 長度:1.590"（40.39mm） 板間高度:1.250"（31.75mm）1 1/4" 安裝類型:鉚釘 材質:尼龍 支撐孔直徑:0.158"（4.00mm） 支撐面板厚度:0.070"（1.78mm） 安裝孔直徑:0.187"（4.75mm）3/16" 安裝面板厚度:0.047 ~ 0.105"（1.20 ~ 2.67mm） 其它名稱:61063012REHCBS2001 |
發布緊急采購，3分鐘左右您將得到回復。