- 您現在的位置：買賣IC網 > PDF目錄370021 > PSD813F4V -200V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-2 package; A IRHNA597260 with Standard Packaging PDF資料下載
參數資料
| 型號： | PSD813F4V |
| 英文描述： | -200V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-2 package; A IRHNA597260 with Standard Packaging |
| 中文描述： | Flash在系統編程（ISP）外設的8位微控制器 |
| 文件頁數： | 65/103頁 |
| 文件大小： | 1185K |
| 代理商： | PSD813F4V |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
65/103
PSD81XFX, PSD83XF2, PSD85XF2
PROGRAMMING IN-CIRCUIT USING THE JTAG SERIAL INTERFACE
The JTAG Serial Interface block can be enabled
on Port C (see Table 34). All memory blocks (pri-
mary and secondary Flash memory), PLD logic,
and PSD8XXFX Configuration Register bits may
be programmed through the JTAG Serial Interface
block. A blank device can be mounted on a printed
circuit board and programmed using JTAG.
The standard JTAG signals (IEEE 1149.1) are
TMS, TCK, TDI, and TDO. Two additional signals,
TSTAT and TERR, are optional JTAG extensions
used to speed up Program and Erase cycles.
By default, on a blank PSD8XXFX (as shipped
from the factory or after erasure), four pins on Port
C are enabled for the basic JTAG signals TMS,
TCK, TDI, and TDO
See Application Note AN1153for more details on
JTAG In-System Programming (ISP).
Standard JTAG Signals
The standard JTAG signals (TMS, TCK, TDI, and
TDO) can be enabled by any of three different con-
ditions that are logically ORed. When enabled,
TDI, TDO, TCK, and TMS are inputs, waiting for a
JTAG serial command from an external JTAG con-
troller device (such as FlashLINK or Automated
Test Equipment). When the enabling command is
received, TDO becomes an output and the JTAG
channel is fully functional inside the PSD8XXFX.
The same command that enables the JTAG chan-
nel may optionally enable the two additional JTAG
signals, TSTAT and TERR.
The following symbolic logic equation specifies the
conditions enabling the four basic JTAG signals
(TMS, TCK, TDI, and TDO) on their respective
Port C pins. For purposes of discussion, the logic
label JTAG_ON is used. When JTAG_ON is true,
the four pins are enabled for JTAG. When
JTAG_ON is false, the four pins can be used for
general PSD8XXFX I/O.
JTAG_ON = PSDsoft_enabled +
/* An NVM configuration bit inside
the PSD is set by the designer in
the PSDsoft Express Configuration
utility. This dedicates the pins
for JTAG at all times (compliant
with IEEE 1149.1 */
Microcontroller_enabled +
/* The microcontroller can set a
bit at run-time by writing to the
PSD register, JTAG Enable. This
register is located at address
CSIOP + offset C7h. Setting the
JTAG_ENABLE bit in this register
will enable the pins for JTAG use.
This bit is cleared by a PSD reset
or the microcontroller. See Table
35 for bit definition. */
PSD_product_term_enabled;
/* A dedicated product term (PT)
inside the PSD can be used to en-
able the JTAG pins. This PT has
the reserved name JTAGSEL. Once
defined as a node in PSDabel, the
designer can write an equation for
JTAGSEL. This method is used when
the Port C JTAG pins are multi-
plexed with other I/O signals. It
is recommended to logically tie
the node JTAGSEL to the JEN\ sig-
nal on the Flashlink cable when
multiplexing JTAG signals. See Ap-
plication Note 1153 for details.
*/
The state of the PSD Reset (RESET) signal does
not interrupt (or prevent) JTAG operations if the
JTAG pins are dedicated by an NVM configuration
bit (via PSDsoft Express). However, Reset (RE-
SET) will prevent or interrupt JTAG operations if
the JTAG enable register is used to enable the
JTAG pins.
The PSD8XXFX supports JTAG In-System-Con-
figuration (ISC) commands, but not Boundary
Scan. The PSDsoft Express software tool and
FlashLINK JTAG programming cable implement
the JTAG In-System-Configuration (ISC) com-
mands. A definition of these JTAG In-System-
Configuration (ISC) commands and sequences is
defined in a supplemental document available
from ST. This document is needed only as a refer-
ence for designers who use a FlashLINK to pro-
gram their PSD8XXFX.
Table 34. JTAG Port Signals
Port C Pin
JTAG Signals
Description
PC0
TMS
Mode Select
PC1
TCK
Clock
PC3
TSTAT
Status
PC4
TERR
Error Flag
PC5
TDI
Serial Data In
PC6
TDO
Serial Data Out
相關PDF資料 |
PDF描述 |
|---|---|
| PSD813F5V | -60V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-2 package; Similar to IRHNA9064 with optional Total Dose Rating of 300kRads |
| PSD86 | THREE PHASE RECTIFIER BRIDGE |
| PSF101 | WORLD MAGNETICS ULTRA SENSITIVEPRESSURESWITCHES |
| PSG61 | 4 KEY BI-BI CALL |
| PSM-100KPD | Pressure sensor module/Gauge,Differential |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD813F4VA-15J | 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2VA-15J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| PSD813F4VA-15U | 功能描述:SPLD - 簡單可編程邏輯器件 U 511-PSD813F2VA-15U RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| PSD813F5-12JI | 制造商:WSI 功能描述: |
| PSD813F5-15JI | 制造商:WSI 功能描述: |
| PSD813F5-15U | 制造商:WSI 功能描述: 制造商:WSI 功能描述:1M X 1 FLASH, 27 I/O, PIA-GENERAL PURPOSE, PQFP64 |
發布緊急采購，3分鐘左右您將得到回復。