- 您現在的位置：買賣IC網 > PDF目錄368156 > PSD4135G3-15B81I (意法半導體) Flash In-System-Programmable Peripherals for 16-Bit MCUs PDF資料下載
參數資料
| 型號： | PSD4135G3-15B81I |
| 廠商： | 意法半導體 |
| 英文描述： | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| 中文描述： | Flash在系統可編程外設的16位微控制器 |
| 文件頁數： | 64/93頁 |
| 文件大?。?/td> | 503K |
| 代理商： | PSD4135G3-15B81I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁
9.5.3.4 Reset of Flash Erase and Programming Cycles
An external reset on the RESET pin will also reset the internal Flash memory state
machine. When the Flash is in programming or erase mode, the RESET pin will terminate
the programming or erase operation and return the Flash back to read mode in tNLNH-A
(minimum 25 μs) time.
9.6 Programming In-Circuit using the JTAG-ISP Interface
The JTAG-ISP interface on the PSD4000 can be enabled on Port E (see Table 29). All
memory (Flash and Flash Boot Block), PLD logic, and PSD configuration bits may be
programmed through the JTAG-ISC interface. A blank part can be mounted on a printed
circuit board and programmed using JTAG-ISP.
The standard JTAG signals (IEEE 1149.1) are TMS, TCK, TDI, and TDO. Two additional
signals, TSTAT and TERR, are optional JTAG extensions used to speed up program and
erase operations.
Preliminary Information
PSD4000 Series
61
Port E Pin
PE0
PE1
PE2
PE3
PE4
PE5
JTAG Signals
TMS
TCK
TDI
TDO
TSTAT
TERR
Description
Mode Select
Clock
Serial Data In
Serial Data Out
Status
Error Flag
Table 29. JTAG Port Signals
The
PSD4000
Functional
Blocks
(cont.)
*
SR_cod bit in the VM Register are always cleared to zero on power on or warm reset.
Port Configuration
MCU I/O
PLD Output
Power On Reset
Input Mode
Valid after internal
PSD configuration
bits are loaded
Tri-stated
Tri-stated
Warm Reset
Input Mode
Valid
Power Down Mode
Unchanged
Depend on inputs to
PLD (address are
blocked in PD mode)
Not defined
Tri-stated
Address Out
Data Port
Tri-stated
Tri-stated
Table 28. Status During Power On Reset, Warm Reset and Power Down Mode
Register
Power On Reset
Cleared to
“
0
”
Initialized based on
the selection in
PSDsoft
Configuration Menu.
Cleared to
“
0
”
Warm Reset
Unchanged
Initialized based on
the selection in
PSDsoft
Configuration Menu.
Cleared to
“
0
”
Power Down Mode
Unchanged
Unchanged
PMMR0, 2
VM Register*
All other registers
Unchanged
By default, on a blank PSD (as shipped from factory or after erasure), four pins on Port E
are enabled for the basic JTAG signals TMS, TCK, TDI, and TDO.
See Application Note 54 for more details on JTAG In-System-Programming.
相關PDF資料 |
PDF描述 |
|---|---|
| PSD4135G3-15J | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15JI | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15M | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15MI | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15U | Flash In-System-Programmable Peripherals for 16-Bit MCUs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD4135G3-15J | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15JI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15M | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15MI | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
| PSD4135G3-15U | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash In-System-Programmable Peripherals for 16-Bit MCUs |
發布緊急采購，3分鐘左右您將得到回復。