- 您現在的位置：買賣IC網 > PDF目錄368150 > PSD411A1-15J Field-Programmable Peripheral PDF資料下載
參數資料
| 型號： | PSD411A1-15J |
| 英文描述： | Field-Programmable Peripheral |
| 中文描述： | 現場可編程外圍 |
| 文件頁數： | 73/123頁 |
| 文件大?。?/td> | 657K |
| 代理商： | PSD411A1-15J |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁當前第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁
PSD4XX Famly
70
9.5.2 Oher Power Saving Options
The PSD4XX provides additional power saving options. These options, except the SRAM
Standby Mode, can be enabled/disabled by setting up the corresponding bit in the PMMR.
J
EPROM
The EPROM power consumption in the PSD is controlled by bit 3 in the
PMMR0 – EPROM CMiser. Upon reset the CMiser bit is OFF. This will cause the
EPROM to be ON at all times as long as CSI is enabled (low). The reason this mode is
provided is to reduce the access time of the EPROM by 10 ns relative to the low power
condition when CMiser is ON. If CSI is disabled (high) the EPROM will be deselected
and will enter standby mode (OFF) overriding the state of the CMiser.
If CMiser is set (ON) then the EPROM will enter the standby mode when not selected.
This condition can take place when CSI is high or when CSI is low and the EPROM is
not accessed. For example, if the MCU is accessing the SRAM, the EPROM will be
deselected and will be in low power mode.
An additional advantage of the CMiser is achieved when the PSD is configured in the
by 8 mode (8 bit data bus). In this case an additional power savings is achieved in the
EPROM (and also in the SRAM) by turning off 1/2 of the array even when the EPROM
is accessed (the array is divided internally into odd and even arrays).
The power consumption for the different EPROM modes is given in the DC
Characteristics table under I
CC
(DC) EPROM Adder.
J
SRAM Standby Mode
The SRAM has a dedicated supply voltage V
STBY
that can be used to connect a battery.
When V
CC
becomes lower than V
STBY
–0.6 then the PSD will automatically connect
the V
STBY
as a power source to the SRAM. The SRAM Standby Current (I
STBY
) is
typically 0.5 μA.
SRAM data retention voltage V
DF
is 2 V minimum.
J
Zero Power ZPLD
ZPLD power/speed is controlled by the ZPLD_Turbo bit (bit 4) in the PMMR0.
After reset the ZPLD is in Turbo mode and runs at full power and speed. By setting the
bit to “1”, the Turbo mode is disabled and the ZPLD is consuming Zero Power current if
the inputs are not switching for an extended time of 70 ns. The propagation delay time
will be increased by 10ns after the Turbo bit is set to “1” (turned off) if the inputs change
at a frequency of less than 15 MHz.
The PSD4XX
Architecture
(cont.)
相關PDF資料 |
PDF描述 |
|---|---|
| PSD411A1-15JI | 100V 100kRad Hi-Rel Single N-Channel TID Hardened MOSFET in a TO-204AA package; A IRH7130 with Standard Packaging |
| PSD411A1-15LI | -60V 100kRad Hi-Rel Single P-Channel TID Hardened MOSFET in a SMD-0.5 package; Similar to IRHNJ597034 with optional Total Dose Rating of 300kRads |
| PSD411A1-15U | 400V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a TO-205AF package; A IRHF7310SE with Standard Packaging |
| PSD411A1-15UI | 250V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a TO-205AF package; JANS Certified Part Number |
| PSD411A1-20J | 250V 100kRad Hi-Rel Single N-Channel SEE Hardened MOSFET in a SMD-2 package; JANS Certified device. Equivalent to IR Part Number IRHNA57264SE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD411A1-15JI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD411A1-15LI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD411A1-15U | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD411A1-15UI | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
| PSD411A1-20J | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field-Programmable Peripheral |
發布緊急采購，3分鐘左右您將得到回復。