<nobr id="qrbxp"><noframes id="qrbxp">
<thead id="qrbxp"><sup id="qrbxp"><rt id="qrbxp"></rt></sup></thead>
  • <pre id="qrbxp"><menu id="qrbxp"><nobr id="qrbxp"></nobr></menu></pre>
  • <thead id="qrbxp"></thead>
    參數資料
    型號: PSD313V-70J
    廠商: 意法半導體
    英文描述: Low Cost Field Programmable Microcontroller Peripherals
    中文描述: 低成本現場可編程微控制器外圍設備
    文件頁數: 10/85頁
    文件大?。?/td> 691K
    代理商: PSD313V-70J
    PSD3XX Famly
    7
    7.0
    ZPSD
    Background
    (cont.)
    Integrated Power Management
    TM
    Operation
    Upon each address or logic input change to the ZPSD, the device powers up from low
    power standby for a short time. Then the ZPSD consumes only the necessary power to
    deliver new logic or memory data to its outputs as a response to the input change. After the
    new outputs are stable, the ZPSD latches them and automatically reverts back to standby
    mode. The I
    CC
    current flowing during standby mode and during DC operation is identical
    and is only a few microamperes.
    The ZPSD automatically reduces its DC current drain to these low levels and does not
    require controlling by the CSI (Chip Select Input). Disabling the CSI pin unconditionally
    forces the ZPSD to standby mode independent of other input transitions.
    The only significant power consumption in the ZPSD occurs during AC operation.
    The ZPSD contains the first architecture to apply zero power techniques to memory and
    logic blocks.
    Figure 2 compares ZPSD zero power operation to the operation of a discrete solution.
    A standard microcontroller (MCU) bus cycle usually starts with an ALE (or AS) pulse and
    the generation of an address. The ZPSD detects the address transition and powers up for a
    short time. The ZPSD then latches the outputs of the PAD, EPROM and SRAM to the new
    values. After finishing these operations, the ZPSD shuts off its internal power, entering
    standby mode. The time taken for the entire cycle is less than the ZPSD’s “access time.”
    The ZPSD will stay in standby mode while its inputs are not changing between bus cycles.
    In an alternate system implementation using discrete EPROM, SRAM, and other discrete
    components, the system will consume operating power during the entire bus cycle. This
    is because the chip select inputs on the memory devices are usually active throughout
    the entire cycle. The AC power consumption of the ZPSD may be calculated using the
    composite frequency of the MCU address and control signals, as well as any other logic
    inputs to the ZPSD.
    ALE
    DISCRETE EPROM, SRAM & LOGIC
    ADDRESS
    EPROM
    ACCESS
    SRAM
    ACCESS
    EPROM
    ACCESS
    I
    CC
    ZPSD
    ZPSD
    ZPSD
    TIME
    Figure 2. ZPSDPower Operation vs. Dscrete Implementation
    相關PDF資料
    PDF描述
    PSD301-25J Low Cost Field Programmable Microcontroller Peripherals
    PSD301-25JI Low Cost Field Programmable Microcontroller Peripherals
    PSD301-25JM Low Cost Field Programmable Microcontroller Peripherals
    PSD301-70J 1/2" CASE HARDENED STEEL LOCKNUT
    PSD301-70JI Low Cost Field Programmable Microcontroller Peripherals
    相關代理商/技術參數
    參數描述
    PSD313V-70JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
    PSD313V-70JM 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
    PSD313V-90J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
    PSD313V-90JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
    PSD313V-90JM 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals