參數資料
型號： PSD211R-B-70L
廠商： 意法半導體
英文描述： Low Cost Field Programmable Microcontroller Peripherals
中文描述： 低成本現場可編程微控制器外圍設備
文件頁數： 26/51頁
文件大?。?/td> 348K
代理商： PSD211R-B-70L
PSD211R Famly
23
15.0
Security Mode
Security Mode in the PSD211R locks the contents of PAD A, PAD B, and all the
configuration bits. The EPROM and I/O contents can be accessed only through the PAD.
The Security Mode must be set by PSDsoft prior to run-time. The Security Bit can only be
erased on the UV parts using a full-chip erase. If Security Mode is enabled, the contents of
the PSD211R can not be uploaded (copied) on a device programmer.
16.0
Power
Management
PSDs from all 211R families use zero-power memory techniques that place memory into
Standby Mode between MCU accesses. The memory becomes active briefly after an
address transition, then delivers new data to the outputs, latches the outputs, and returns to
Standby. This is done automatically and the designer has to do nothing special to benefit
from this feature.
In addition to the benefits of Zero-power memory technology, there are ways to gain
additional savings. The following factors determine how much current the entire PSD device
uses:
Use of CSI (Chip Select Input)
Setting of the CMiser bit
Setting of the Turbo Bit (ZPSD only)
The number of product terms used in the PAD
The composite frequency of the input signals to the PAD
The loading on I/O pins.
The total current consumption for the PSD is calculated by summing the currents from
memory, PAD logic, and I/O pins, based on your design parameters and the power
management options used.
16.1 CSI Input
Driving the CSI pin inactive (logic 1) disables the inputs of the PSD and forces the entire
PSD to enter Power-down Mode, independent of any transition on the MCU bus (address
and control) or other PSD inputs. During this time, the PSD device draws only standby
current (micro-amps). Alternately, driving a logic 0 on the CSI pin returns the PSD to normal
operation. See Tables 7A and 7B for information on signal states during Power-down Mode.
The CSI pin feature is available only if enabled in the PSDsoft Configuration utility.
16.2 CMiser bit
In addition to power savings resulting from the Zero-power technology used in the memory,
the CMiser feature saves even more power under certain conditions. Savings are
significant when the PSD is configured for an 8-bit data path because the CMiser feature
turns off half of the array when memory is being accessed (the memory is divided internally
into odd and even arrays). See the DC characteristics table for current usage related to the
CMiser bit.
You should keep the following in mind when using this bit:
Setting of this bit is accomplished with PSDsoft at the design stage, prior to run-time.
Memory access times are extended by 10 nsec for standard voltage (non-V) devices,
and 20 nsec for low voltage (V) devices.
相關PDF資料
PDF描述
PSD211R-B-70M Low Cost Field Programmable Microcontroller Peripherals
PSD211R-B-90J Low Cost Field Programmable Microcontroller Peripherals
PSD211R-B-90JI Low Cost Field Programmable Microcontroller Peripherals
PSD211RL Low Cost Field Programmable Microcontroller Peripherals
PSD211RM Low Cost Field Programmable Microcontroller Peripherals
相關代理商/技術參數
參數描述
PSD211R-B-70M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD211R-B-90J 制造商:WSI 功能描述:
PSD211R-B-90JI 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD211RL 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
PSD211RM 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*