- 您現在的位置：買賣IC網 > PDF目錄383784 > PSD211R-B-15L (意法半導體) Low Cost Field Programmable Microcontroller Peripherals PDF資料下載
參數資料
| 型號： | PSD211R-B-15L |
| 廠商： | 意法半導體 |
| 英文描述： | Low Cost Field Programmable Microcontroller Peripherals |
| 中文描述： | 低成本現場可編程微控制器外圍設備 |
| 文件頁數： | 19/51頁 |
| 文件大?。?/td> | 348K |
| 代理商： | PSD211R-B-15L |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
PSD211R Famly
16
11.0
PSDMemory
The following sections explain the EPROM memory block and how to program and erase
the PSD211R.
11.1 EPROM
For all PSD211R devices, the EPROM is built using Zero-power technology. This means
that the EPROM powers up only when the address changes. It consumes power for the
necessary time to latch data on its outputs. After this, it powers down and remains in
standby mode until the next address change. This happens automatically, and the designer
has to do nothing special.
The 32K x 8 EPROM is divided into eight equal-sized banks. Each bank can be placed in
any address location by programming the PAD. Bank0-Bank7 are selected by PAD A
outputs ES0-ES7, respectively. There is one product term for each bank select (ESi).
11.2 Programmng and Erasure
Programming the device can be done using the following methods:
WSI’s main programmer—PSDpro—which is accessible through a parallel port.
WSI’s programmer used specifically with the PSD211R—PEP300.
WSI’s discontinued programmer—Magic Pro.
A 3rd party programmer, such as Data I/O.
Information for programming the device is available directly from WSI. Please contact your
local sales representative. Also, check our web site (waferscale.com) for information related
to 3rd party programmers.
Upon delivery from WSI, or after each erasure (using windowed part), the PSD211R device
has all bits in the PAD and EPROM in the HI state (logic 1). The configuration bits are in the
LO state (logic 0).
To clear all locations of their programmed contents (assuming you have a windowed
version), expose the windowed device to an Ultra-Violet (UV) light source. A dosage of
30 W second/cm
2
is required for PSD211R devices, and 40 W second/cm
2
for low-voltage
(V suffix) devices. This dosage can be obtained with exposure to a wavelength of
2537 and intensity of 12000 μW/cm
2
for 40 to 45 minutes for the PSD211R and 55 to 60
minutes for the low-voltage (V suffix) devices. The device should be approximately 1 inch
(2.54 cm) from the source, and all filters should be removed from the UV light source prior
to erasure.
The PSD211R devices will erase with light sources having wavelengths shorter than
4000 . However, the erasure times will be much longer than when using the
recommended 2537 wavelength. Note: exposure to sunlight will eventually erase the
device. If used in such an environment, the package window should be covered with an
opaque substance.
12.0
Control Signals
Consult your MCU data sheet to determine which control signals your MCU generates, and
how they operate. This section is intended to show which control signals should be
connected to what pins on the PSD211R. You will then use PSDsoft to configure the
PSD211R, based on the combination of control signals that your MCU outputs, for example
RD, WR, and PSEN.
The PSD211R is compatible with the following control signals:
ALE or AS (polarity is programmable)
WR or R/W
RD/E
PSEN
A19/CSI
RESET (polarity is programmable except on low voltage versions with the V suffix).
相關PDF資料 |
PDF描述 |
|---|---|
| PSD211R-B-15M | Low Cost Field Programmable Microcontroller Peripherals |
| PSD211R-B-70J | Low Cost Field Programmable Microcontroller Peripherals |
| PSD211R-B-70L | Low Cost Field Programmable Microcontroller Peripherals |
| PSD211R-B-70M | Low Cost Field Programmable Microcontroller Peripherals |
| PSD211R-B-90J | Low Cost Field Programmable Microcontroller Peripherals |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PSD211R-B-15M | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD211R-B-70J | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD211RB-70J | 功能描述:SPLD - 簡單可編程邏輯器件 U 511-ZPSD301B-70J RoHS:否 制造商:Texas Instruments 邏輯系列:TICPAL22V10Z 大電池數量:10 最大工作頻率:66 MHz 延遲時間:25 ns 工作電源電壓:4.75 V to 5.25 V 電源電流:100 uA 最大工作溫度:+ 75 C 最小工作溫度:0 C 安裝風格:Through Hole 封裝 / 箱體:DIP-24 |
| PSD211R-B-70L | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
| PSD211R-B-70M | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Low Cost Field Programmable Microcontroller Peripherals |
發布緊急采購，3分鐘左右您將得到回復。