- 您現在的位置：買賣IC網 > PDF目錄98057 > PQ48050QNA20PNS (SYNQOR INC) 1-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | PQ48050QNA20PNS |
| 廠商： | SYNQOR INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | QUARTER BRICK PACKAGE-8 |
| 文件頁數： | 13/13頁 |
| 文件大小： | 716K |
| 代理商： | PQ48050QNA20PNS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁
referenced to the return terminal of the 48V input bus. There
are two versions of the
PowerQor series converter that differ
by the sense of the logic used for the ON/OFF input. In the
PQxxyyyQNAzzPxx version, the ON/OFF input is active
high (meaning that a high turns the converter
on). In the
PQxxyyyQNAzzNxx version, the ON/OFF signal is active
low (meaning that a low turns the converter
on). Figure A
details five possible circuits for driving the ON/OFF pin.
Pins 7 and 5 (SENSE(+)): The SENSE(+) inputs correct
for voltage drops along the conductors that connect the con-
verter’s output pins to the load.
Pin 7 should be connected to Vout(+) and Pin 5 should be
connected to Vout(-) at the point on the board where regu-
lation is desired. That is,
[Vout(+) - Vout(-)] – [SENSE(+) - SENSE (-)] < 10%Vout
Pins 7 and 5 must be connected for proper regulation of the
output voltage. However, if these connections are not made,
nothing catastrophic will happen to the converter under nor-
mal operating conditions—the converter will simply deliver
an output voltage that is slightly higher than its specified
value.
Note: the output over-voltage protection circuit senses the
voltage across the output (pins 8 and 4) to determine when
it should trigger, not the voltage across the converter’s sense
pins (pins 7 and 5). Therefore, the resistive drop on the
board should be small enough so that output
OVP does not
trigger, even during load transients.
Pin 6 (TRIM): The TRIM input permits the user to adjust the
output voltage across the sense leads up or down. To lower
the output voltage, the user should connect a resistor
between Pin 6 and Pin 5, which is the SENSE(-) input. To
raise the output voltage, the user should connect a resistor
between Pin 6 and Pin 7, which is the SENSE(+) input.
A resistor connected between Pin 6 and Pin 5 will decrease
the output voltage. For a desired decrease of
percent of
the nominal output voltage, the value of this resistor should
be
Product # PQ48050QNA20
Phone 1-888-567-9596
Doc.# 005-2QN450D_B
9/5/01
Page 9
Technical Specification
48Vin 5.0Vout 20A
Quarter
Brick
Open Collector Enable Circuit
Figure A: Various circuits for driving the ON/OFF pin.
Remote Enable Circuit
Direct Logic Drive
Negative Logic
(Permanently Enabled)
Positive Logic
(Permanently Enabled)
ON/OFF
Vin(_)
ON/OFF
Vin(_)
ON/OFF
5V
TTL/
CMOS
Vin(_)
ON/OFF
Vin(_)
Rtrim-down =
(
511) - 10.22
%
(k
)
=
(VNOM – VDES) x 100%
VNOM
where
VNOM = Nominal Voltage
VDES = Desired Voltage
and
相關PDF資料 |
PDF描述 |
|---|---|
| PQ48050QNA20NRS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PQ48050QNA20NKS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PQ48050QNA20PYS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PQ48050QNA20NNS | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| PQ50050HPB50NNS-G | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PQ480515HTA60NNS | 制造商:SynQor 功能描述: |
| PQ48053HTA30 | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:30 Amp, No Heatsink, Isolated DC/DC Converter |
| PQ48053HTA30NKS | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:30 Amp, No Heatsink, Isolated DC/DC Converter |
| PQ48053HTA30NNS | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:30 Amp, No Heatsink, Isolated DC/DC Converter |
| PQ48053HTA30NRS | 制造商:SYNQOR 制造商全稱:SYNQOR 功能描述:30 Amp, No Heatsink, Isolated DC/DC Converter |
發布緊急采購，3分鐘左右您將得到回復。