
PM100RLA060
Intellimod L-Series
Three Phase IGBT Inverter + Brake
100 Amperes/600 Volts
4
Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272
Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specied
Characteristics
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Control Sector
Short Circuit Trip Level
SC
Inverter Part
200
—
Amperes
(-20°C ≤ Tj ≤ 125°C, VD = 15V)
Brake Part
100
—
Amperes
Short Circuit Current Delay Time
toff(SC)
VD = 15V
—
0.2
—
s
Over Temperature Protection
OT
Trip Level
135
145
155
°C
(Detect Tj of IGBT Chip)
OTR
Reset Level
—
125
—
°C
Supply Circuit Under-voltage Protection
UV
Trip Level
11.5
12.0
12.5
Volts
(-20 ≤ Tj ≤ 125°C)
UVR
Reset Level
—
12.5
—
Volts
Circuit Current
ID
VD = 15V, VCIN = 15V, VN1-VNC
—
20
30
mA
VD = 15V, VCIN = 15V, VXP1-VXPC
—
5
10
mA
Input ON Threshold Voltage
Vth(on)
Applied between UP-VUPC,
1.2
1.5
1.8
Volts
Input OFF Threshold Voltage
Vth(off)
VP-VVPC, WP-VWPC, UN- VN- WN-Br-VNC 1.7
2.0
2.3
Volts
Fault Output Current*
IFO(H)
VD = 15V, VCIN = 15V
—
0.01
mA
IFO(L)
VD = 15V, VCIN = 15V
—
10
15
mA
Fault Output Pulse Width*
tFO
VD = 15V
1.0
1.8
—
ms
*Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower devide operate to protect it.
Thermal Characteristics, Tj = 25°C unless otherwise specied
Characteristic
Symbol
Condition
Min.
Typ.
Max.
Units
Junction to Case Thermal Resistance
Rth(j-c)Q
Inverter IGBT (Per 1/6 Module) (Note 1)
—
0.35
°C/Watt
Rth(j-c)D
Inverter FWDi (Per 1/6 Module) (Note 1)
—
0.56
°C/Watt
Rth(j-c)Q
Brake IGBT (Per 1/6 Module) (Note 1)
—
0.55
°C/Watt
Rth(j-c)D
Brake FWDi (Per 1/6 Module) (Note 1)
—
0.92
°C/Watt
Rth(j-c)Q
Inverter IGBT (Per 1/6 Module) (Note 2)
—
0.27
°C/Watt
Rth(j-c)D
Inverter FWDi (Per 1/6 Module) (Note 2)
—
0.43
°C/Watt
Rth(j-c)Q
Brake IGBT (Per 1/6 Module) (Note 2)
—
0.42
°C/Watt
Rth(j-c)D
Brake FWDi (Per 1/6 Module) (Note 2)
—
0.71
°C/Watt
Contact Thermal Resistance
Rth(c-f)
Case to Fin Per Module,
—
0.038
°C/Watt
Thermal Grease Applied (Note 1)
Recommended Conditions for Use
Characteristic
Symbol
Condition
Value
Units
Supply Voltage
VCC
Applied across P-N Terminals
≤400
Volts
Control Supply Voltage**
VD
Applied between VUP1-VUPC,
15.0 ± 1.5
Volts
VVP1-VVPC, VWP1-VWPC, VN1-VNC
Input ON Voltage
VCIN(on)
Applied between UP-VUPC,
≤0.8
Volts
Input OFF Voltage
VCIN(off)
VP-VVPC, WP-VWPC, UN- VN- WN-Br-VNC
≥9.0
Volts
PWM Input Frequency
fPWM
—
≤20
kHz
Arm Shoot-through Blocking Time
tDEAD
Input Signal
≥2.0
s
** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/s, Variation ≤ 2V peak to peak.