- 您現在的位置：買賣IC網 > PDF目錄385719 > PLY10AN1522R0D2M (Murata Manufacturing Co., Ltd.) EMI Suppression Filters for AC Power Lines PDF資料下載
參數資料
| 型號： | PLY10AN1522R0D2M |
| 廠商： | Murata Manufacturing Co., Ltd. |
| 英文描述： | EMI Suppression Filters for AC Power Lines |
| 中文描述： | 交流電源線路的EMI靜噪濾波器 |
| 文件頁數： | 22/24頁 |
| 文件大?。?/td> | 420K |
| 代理商： | PLY10AN1522R0D2M |
Caution (Rating)
1. Rated Current
Operating current should not exceed the rated
value. Even if operating current is under the
rated value, adequate ventilation is required to
avoid excessive heat generated within the product
(choke coil) and from surrounding heat sources.
If exceeding these conditions, excessive heat may
cause fumes or permanent damage to the product.
Please ensure that product (choke coil) is
evaluated and confirmed against the specification
when it is mounted in your final assembled product.
-> Winding temperature should be less than
120 degree C.
*As for FKOB series winding temperature should be
less than 95 degree C.
Maximum allowable temperature at the surface of
coil (ambient temperature + winding temperature
rise) is in accordance with each safety standard
applicable to final assembled product.
When the temperature at winding exceeds maximum
allowable temperature of safety standard, the
rated current should be derated.
2. Inrush Current
Inrush current should not exceed 10 times rated
current within 1/4 cycle of 50/60Hz commercial
power line. Inrush current should be limited to a
minimum of 10 seconds after last inrush.
If these conditions are exceeded, excessive heat may
cause fumes or permanent damage to the component,
or at worst cause ignition.
I
Notice (Storage and Operating Condition)
1. Soldering Conditions
(1) Flux, Solder
· Rosin-based flux should be used. Do not use strong
acidic flux with halide content exceeding 0.2wt%
(chlorine conversion value)
· Use 63/37 solder (Sn/Pb = 63/37) or 60/40 solder
(Sn/Pb = 60/40). In case of lead-free solder, use
Sn-3.0Ag-0.5Cu solder
(2) Flow soldering profile
2. Cleaning
Avoid cleaning product due to non-waterproof
construction.
3. Storage and Handling Requirements
(1) Storage period
Product should be used within 12 months after receiving.
Solderability should be checked if this period is
exceeded.
(2) Storage conditions
Storage Temperature: -10 to 40
°
C
Relative humidity: 30 to 70%
Avoid sudden changes in temperature and humidity.
Don't keep products in corrosive gases such as sulfur,
chlorine gas or acid, or it may cause oxidation of lead
terminals resulting in poor solderability or corrosion of
component windings.
(3) Handling conditions
Care should be taken when transporting or handling
product to avoid excessive vibration or mechanical shock.
For additional mounting methods, please contact Murata.
Standard profile
Limit profile
Sn/Pb = 60/40, Sn/Pb = 63/37
Sn-3.0Ag-0.5Cu solder
Soldering temp.
240-260
°
C
Soldering time
5s max.
Soldering temp.
250
±
2
°
C
Soldering time
4-6s
Soldering temp.
265
±
3
°
C
Soldering time
5s
Cycle of flow
2 times
Pre-heating
Soldering
Gradual cooling
(in air)
150
°
C
300
250
200
150
100
50
T
°
C
60s min.
Soldering time
Soldering temperature
I
Notice (Soldering and Mounting)
Magnetic Flux Leakage
Choke coils generate small amounts of magnetic flux
leakage that may adversely affect equipment operation
according to component arrangement.
Testing should be completed on final assembly to
ensure equipment performance is not affected.
I
Notice (Rating)
Coil Humming Noise
Magnetic flux generated between coil and core or
between the choke coil windings creates repulsive
power between the coil windings. This repulsive
power causes the coil winding to vibrate and create
a humming noise. The amount of hum produced by the
coil is proportionate to the amount of harmonic
distortion generated by the operating current. This
does not influence the electrical performance of
the coils, but it should be considered and tested
in actual circuit application.
相關PDF資料 |
PDF描述 |
|---|---|
| PLY10AN1522R0P2B | EMI Suppression Filters for AC Power Lines |
| PLY10AN1522R0P2M | EMI Suppression Filters for AC Power Lines |
| PLY10AN1522R0R2B | EMI Suppression Filters for AC Power Lines |
| PLY10AN1522R0R2M | EMI Suppression Filters for AC Power Lines |
| PLY10AS1522R0A2B | EMI Suppression Filters for AC Power Lines |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PLY10AN1522R0P2B | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:EMI Suppression Filters for AC Power Lines |
| PLY10AN1522R0P2M | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:EMI Suppression Filters for AC Power Lines |
| PLY10AN1522R0R2B | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:EMI Suppression Filters for AC Power Lines |
| PLY10AN1522R0R2M | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:EMI Suppression Filters for AC Power Lines |
| PLY10AN2121R4R2B | 功能描述:共模濾波器/扼流器 2.1mH/150uH 1.4A AC Line Filter RoHS:否 制造商:TDK 電感: 阻抗:35 Ohms 容差: 最大直流電流:0.1 A 最大直流電阻:1.5 Ohms 自諧振頻率: Q 最小值: 工作溫度范圍:- 25 C to + 85 C 端接類型:SMD/SMT 封裝 / 箱體:0302 (0806 metric) 系列:TCE |
發布緊急采購，3分鐘左右您將得到回復。