<li id="oq3kl"><pre id="oq3kl"><div id="oq3kl"></div></pre></li>
    • <button id="oq3kl"><input id="oq3kl"></input></button>
  • <button id="oq3kl"><tbody id="oq3kl"></tbody></button>
    參數資料
    型號： PIC18LF8720-I/PT
    廠商： Microchip Technology
    文件頁數： 15/165頁
    文件大?。?/td> 0K
    描述： IC MCU FLASH 64KX16 LV 80-TQFP
    產品培訓模塊： Asynchronous Stimulus
    8-bit PIC® Microcontroller Portfolio
    標準包裝： 119
    系列： PIC® 18F
    核心處理器： PIC
    芯體尺寸： 8-位
    速度： 25MHz
    連通性： EBI/EMI，I²C，SPI，UART/USART
    外圍設備： 欠壓檢測/復位，LVD，POR，PWM，WDT
    輸入/輸出數： 68
    程序存儲器容量： 128KB（64K x 16）
    程序存儲器類型： 閃存
    EEPROM 大?。?/td> 1K x 8
    RAM 容量： 3.75K x 8
    電壓 - 電源 (Vcc/Vdd)： 2 V ~ 5.5 V
    數據轉換器： A/D 16x10b
    振蕩器型： 外部
    工作溫度： -40°C ~ 85°C
    封裝/外殼： 80-TQFP
    包裝： 托盤
    2004 Microchip Technology Inc.
    DS39609B-page 109
    PIC18F6520/8520/6620/8620/6720/8720
    10.3
    PORTC, TRISC and LATC
    Registers
    PORTC is an 8-bit wide, bidirectional port. The corre-
    sponding data direction register is TRISC. Setting a
    TRISC bit (= 1) will make the corresponding PORTC
    pin an input (i.e., put the corresponding output driver in
    a high-impedance mode). Clearing a TRISC bit (= 0)
    will make the corresponding PORTC pin an output (i.e.,
    put the contents of the output latch on the selected pin).
    The Data Latch register (LATC) is also memory
    mapped. Read-modify-write operations on the LATC
    register, read and write the latched output value for
    PORTC.
    PORTC is multiplexed with several peripheral functions
    (Table 10-5). PORTC pins have Schmitt Trigger input
    buffers.
    When enabling peripheral functions, care should be
    taken in defining TRIS bits for each PORTC pin. Some
    peripherals override the TRIS bit to make a pin an
    output, while other peripherals override the TRIS bit to
    make a pin an input. The user should refer to the
    corresponding peripheral section for the correct TRIS
    bit settings.
    The pin override value is not loaded into the TRIS
    register. This allows read-modify-write of the TRIS
    register, without concern due to peripheral overrides.
    RC1 is normally configured by configuration bit,
    CCP2MX, as the default peripheral pin of the CCP2
    module (default/erased state, CCP2MX = 1).
    EXAMPLE 10-3:
    INITIALIZING PORTC
    FIGURE 10-8:
    PORTC BLOCK DIAGRAM (PERIPHERAL OUTPUT OVERRIDE)
    Note:
    On a Power-on Reset, these pins are
    configured as digital inputs.
    CLRF
    PORTC
    ; Initialize PORTC by
    ; clearing output
    ; data latches
    CLRF
    LATC
    ; Alternate method
    ; to clear output
    ; data latches
    MOVLW
    0xCF
    ; Value used to
    ; initialize data
    ; direction
    MOVWF
    TRISC
    ; Set RC<3:0> as inputs
    ; RC<5:4> as outputs
    ; RC<7:6> as inputs
    PORTC/Peripheral Out Select
    Data Bus
    WR LATC
    WR TRISC
    Data
    Latch
    TRIS Latch
    RD TRISC
    Q
    D
    Q
    CK
    QD
    EN
    Peripheral Data Out
    0
    1
    Q
    D
    Q
    CK
    P
    N
    VDD
    VSS
    RD PORTC
    Peripheral Data In
    I/O pin(1)
    or
    WR PORTC
    RD LATC
    Schmitt
    Trigger
    Note 1:
    I/O pins have diode protection to VDD and VSS.
    2:
    Peripheral Output Enable is only active if Peripheral Select is active.
    TRIS
    Override
    Peripheral Output
    Logic
    TRIS OVERRIDE
    Pin
    Override
    Peripheral
    RC0
    Yes
    Timer1 Osc for
    Timer1/Timer3
    RC1
    Yes
    Timer1 Osc for
    Timer1/Timer3,
    CCP2 I/O
    RC2
    Yes
    CCP1 I/O
    RC3
    Yes
    SPI/I2C
    Master Clock
    RC4
    Yes
    I2C Data Out
    RC5
    Yes
    SPI Data Out
    RC6
    Yes
    USART1 Async
    Xmit, Sync Clock
    RC7
    Yes
    USART1 Sync
    Data Out
    Enable(2)
    相關PDF資料
    PDF描述
    PIC18LF8722-I/PT IC PIC MCU FLASH 64KX16 80TQFP
    PIC18LF96J65-I/PT IC PIC MCU FLASH 48KX16 100TQFP
    PIC24F16KL401-I/P IC MCU 16BIT 16KB FLASH 20-PDIP
    PIC24FJ128GA010-I/PF IC PIC MCU FLASH 128KB 100TQFP
    PIC24FJ256GA110-I/PF IC PIC MCU FLASH 256K 100TQFP
    相關代理商/技術參數
    參數描述
    PIC18LF8720T-I/PT 功能描述:8位微控制器 -MCU 128KB 3840 RAM 68I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
    PIC18LF8721-I/PT 功能描述:8位微控制器 -MCU 128kBF 4096RM 40MHz nonoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
    PIC18LF8721T-I/PT 功能描述:8位微控制器 -MCU 128kBF 4096RM 40MHz nonoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
    PIC18LF8722-I/PT 功能描述:8位微控制器 -MCU 128 KB FL 4K RAM 70 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
    PIC18LF8722-I/PT 制造商:Microchip Technology Inc 功能描述:8-Bit Microcontroller IC
    發布緊急采購，3分鐘左右您將得到回復。

    采購需求

    (若只采購一條型號，填寫一行即可)

    發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

    發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

    *型號 *數量 廠商 批號 封裝
    添加更多采購

    我的聯系方式

    *
    *
    *