參數資料
型號： PIC18F67J11-I/PT
廠商： Microchip Technology
文件頁數： 46/107頁
文件大?。?/td> 0K
描述： IC PIC MCU FLASH 64KX16 64TQFP
產品培訓模塊： Asynchronous Stimulus
PIC18 J Series MCU Overview
8-bit PIC® Microcontroller Portfolio
標準包裝： 160
系列： PIC® 18F
核心處理器： PIC
芯體尺寸： 8-位
速度： 48MHz
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，LVD，POR，PWM，WDT
輸入/輸出數： 52
程序存儲器容量： 128KB（64K x 16）
程序存儲器類型： 閃存
RAM 容量： 3930 x 8
電壓 - 電源 (Vcc/Vdd)： 2 V ~ 3.6 V
數據轉換器： A/D 11x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 64-TQFP
包裝： 托盤
產品目錄頁面： 644 (CN2011-ZH PDF)
配用： AC162091-ND - HEADER MPLAB ICD2 18F87J11 64/80
MA180020-ND - MODULE PLUG-IN HPC EXPL 18F87J11
AC164327-ND - MODULE SKT FOR 64TQFP
2007-2012 Microchip Technology Inc.
DS39778E-page 43
PIC18F87J11 FAMILY
3.5
Internal Oscillator Block
The PIC18F87J11 family of devices includes an
internal oscillator block which generates two different
clock signals; either can be used as the microcon-
troller’s clock source. This may eliminate the need for
an external oscillator circuit on the OSC1 and/or OSC2
pins.
The main output is the Fast RC oscillator, or INTOSC,
an 8 MHz clock source which can be used to directly
drive the device clock. It also drives a postscaler, which
can provide a range of clock frequencies from 31 kHz
to 4 MHz. INTOSC is enabled when a clock frequency
from 125 kHz to 8 MHz is selected. The INTOSC out-
put can also be enabled when 31 kHz is selected,
depending on the INTSRC bit (OSCTUNE<7>).
The other clock source is the internal RC oscillator
(INTRC), which provides a nominal 31 kHz output.
INTRC is enabled if it is selected as the device clock
source; it is also enabled automatically when any of the
following are enabled:
Power-up Timer
Fail-Safe Clock Monitor
Watchdog Timer
Two-Speed Start-up
These features are discussed in greater detail in
The clock source frequency (INTOSC direct, INTOSC
with postscaler or INTRC direct) is selected by config-
uring the IRCFx bits of the OSCCON register. The
default frequency on device Resets is 4 MHz.
3.5.1
INTIO MODES
Using the internal oscillator as the clock source elimi-
nates the need for up to two external oscillator pins,
which can then be used for digital I/O. Two distinct
oscillator configurations, which are determined by the
FOSCx Configuration bits, are available:
In INTIO1 mode, the OSC2 pin outputs FOSC/4,
while OSC1 functions as RA7 (see Figure 3-6) for
digital input and output.
In INTIO2 mode, OSC1 functions as RA7 and
OSC2 functions as RA6 (see Figure 3-7), both for
digital input and output.
FIGURE 3-6:
INTIO1 OSCILLATOR MODE
FIGURE 3-7:
INTIO2 OSCILLATOR MODE
3.5.2
INTPLL MODES
The 4x Phase Locked Loop (PLL) can be used with the
internal oscillator block to produce faster device clock
speeds than are normally possible with the internal
oscillator sources. When enabled, the PLL produces a
clock speed of 16 MHz or 32 MHz.
PLL operation is controlled through software. The con-
trol bit, PLLEN (OSCTUNE<6>), is used to enable or
disable its operation. The PLL is available only to
INTOSC when the device is configured to use one of
the INTPLL modes as the primary clock source
(FOSC<2:0> = 011 or 010). Additionally, the PLL will
only function when the selected output frequency is
either 4 MHz or 8 MHz (OSCCON<6:4> = 111 or 110).
Like the INTIO modes, there are two distinct INTPLL
modes available:
In INTPLL1 mode, the OSC2 pin outputs FOSC/4,
while OSC1 functions as RA7 for digital input and
output. Externally, this is identical in appearance
to INTIO1 (Figure 3-6).
In INTPLL2 mode, OSC1 functions as RA7 and
OSC2 functions as RA6, both for digital input and
output. Externally, this is identical to INTIO2
PIC18F87J11
OSC2
FOSC/4
I/O (OSC1)
RA7
PIC18F87J11
I/O (OSC2)
RA6
I/O (OSC1)
RA7
相關PDF資料
PDF描述
PIC18LF44J11-I/PT IC PIC MCU FLASH 16K 2V 44-TQFP
PIC18F44J11-I/PT IC PIC MCU FLASH 16KB 44-TQFP
PIC32MX120F032B-I/ML IC MCU 32BIT 32KB FLASH 28QFN
PIC18LF26K22-I/SO IC PIC MCU 64KB FLASH 28SOIC
PIC32MX210F016B-I/SP MCU 32BIT 16KB FLASH 28SPDIP
相關代理商/技術參數
參數描述
PIC18F67J11T-I/PT 功能描述:8位微控制器 -MCU 128KB Flash 3936 bytesRAM 51I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F67J50-I/PT 功能描述:8位微控制器 -MCU 128KB FLH 3936Bs RAM USB 2.0 nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F67J50T-I/PT 功能描述:8位微控制器 -MCU 128KB FLH 3936Bs RAM USB 2.0 nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F67J60-I/PT 功能描述:8位微控制器 -MCU 128KB FL 12KB RAM 10BASE-T RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC18F67J60T-I/PT 功能描述:8位微控制器 -MCU 128KB FL 12KB RAM 10BASE-T RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*