- 鎮ㄧ従(xi脿n)鍦ㄧ殑浣嶇疆锛�璨疯常IC缍�(w菐ng) > PDF鐩寗3879 > PIC18F4439-E/P (Microchip Technology)IC PIC MCU FLASH 6KX16 40DIP PDF璩囨枡涓嬭級
鍙冩暩(sh霉)璩囨枡
| 鍨嬭櫉(h脿o)锛� | PIC18F4439-E/P |
| 寤犲晢锛� | Microchip Technology |
| 鏂囦欢闋佹暩(sh霉)锛� | 70/322闋� |
| 鏂囦欢澶�?銆�?/td> | 0K |
| 鎻忚堪锛� | IC PIC MCU FLASH 6KX16 40DIP |
| 妯�(bi膩o)婧�(zh菙n)鍖呰锛� | 10 |
| 绯诲垪锛� | PIC® 18F |
| 鏍稿績铏曠悊鍣細 | PIC |
| 鑺珨灏哄锛� | 8-浣� |
| 閫熷害锛� | 40MHz |
| 閫ｉ€氭€э細 | I²C锛孲PI锛孶ART/USART |
| 澶栧湇瑷�(sh猫)鍌欙細 | 娆犲妾㈡脯(c猫)/寰�(f霉)浣�锛孡VD锛孭OR锛孭WM锛學DT |
| 杓稿叆/杓稿嚭鏁�(sh霉)锛� | 32 |
| 绋嬪簭瀛樺劜(ch菙)鍣ㄥ閲忥細 | 12KB锛�6K x 16锛� |
| 绋嬪簭瀛樺劜(ch菙)鍣ㄩ鍨嬶細 | 闁冨瓨 |
| EEPROM 澶�?銆�?/td> | 256 x 8 |
| RAM 瀹归噺锛� | 640 x 8 |
| 闆诲 - 闆绘簮 (Vcc/Vdd)锛� | 4.2 V ~ 5.5 V |
| 鏁�(sh霉)鎿�(j霉)杞�(zhu菐n)鎻涘櫒锛� | A/D 8x10b |
| 鎸暕鍣ㄥ瀷锛� | 鍏�(n猫i)閮� |
| 宸ヤ綔婧害锛� | -40°C ~ 125°C |
| 灏佽/澶栨锛� | 40-DIP锛�0.600"锛�15.24mm锛� |
| 鍖呰锛� | 绠′欢 |
绗�1闋�绗�2闋�绗�3闋�绗�4闋�绗�5闋�绗�6闋�绗�7闋�绗�8闋�绗�9闋�绗�10闋�绗�11闋�绗�12闋�绗�13闋�绗�14闋�绗�15闋�绗�16闋�绗�17闋�绗�18闋�绗�19闋�绗�20闋�绗�21闋�绗�22闋�绗�23闋�绗�24闋�绗�25闋�绗�26闋�绗�27闋�绗�28闋�绗�29闋�绗�30闋�绗�31闋�绗�32闋�绗�33闋�绗�34闋�绗�35闋�绗�36闋�绗�37闋�绗�38闋�绗�39闋�绗�40闋�绗�41闋�绗�42闋�绗�43闋�绗�44闋�绗�45闋�绗�46闋�绗�47闋�绗�48闋�绗�49闋�绗�50闋�绗�51闋�绗�52闋�绗�53闋�绗�54闋�绗�55闋�绗�56闋�绗�57闋�绗�58闋�绗�59闋�绗�60闋�绗�61闋�绗�62闋�绗�63闋�绗�64闋�绗�65闋�绗�66闋�绗�67闋�绗�68闋�绗�69闋�鐣�(d膩ng)鍓嶇70闋�绗�71闋�绗�72闋�绗�73闋�绗�74闋�绗�75闋�绗�76闋�绗�77闋�绗�78闋�绗�79闋�绗�80闋�绗�81闋�绗�82闋�绗�83闋�绗�84闋�绗�85闋�绗�86闋�绗�87闋�绗�88闋�绗�89闋�绗�90闋�绗�91闋�绗�92闋�绗�93闋�绗�94闋�绗�95闋�绗�96闋�绗�97闋�绗�98闋�绗�99闋�绗�100闋�绗�101闋�绗�102闋�绗�103闋�绗�104闋�绗�105闋�绗�106闋�绗�107闋�绗�108闋�绗�109闋�绗�110闋�绗�111闋�绗�112闋�绗�113闋�绗�114闋�绗�115闋�绗�116闋�绗�117闋�绗�118闋�绗�119闋�绗�120闋�绗�121闋�绗�122闋�绗�123闋�绗�124闋�绗�125闋�绗�126闋�绗�127闋�绗�128闋�绗�129闋�绗�130闋�绗�131闋�绗�132闋�绗�133闋�绗�134闋�绗�135闋�绗�136闋�绗�137闋�绗�138闋�绗�139闋�绗�140闋�绗�141闋�绗�142闋�绗�143闋�绗�144闋�绗�145闋�绗�146闋�绗�147闋�绗�148闋�绗�149闋�绗�150闋�绗�151闋�绗�152闋�绗�153闋�绗�154闋�绗�155闋�绗�156闋�绗�157闋�绗�158闋�绗�159闋�绗�160闋�绗�161闋�绗�162闋�绗�163闋�绗�164闋�绗�165闋�绗�166闋�绗�167闋�绗�168闋�绗�169闋�绗�170闋�绗�171闋�绗�172闋�绗�173闋�绗�174闋�绗�175闋�绗�176闋�绗�177闋�绗�178闋�绗�179闋�绗�180闋�绗�181闋�绗�182闋�绗�183闋�绗�184闋�绗�185闋�绗�186闋�绗�187闋�绗�188闋�绗�189闋�绗�190闋�绗�191闋�绗�192闋�绗�193闋�绗�194闋�绗�195闋�绗�196闋�绗�197闋�绗�198闋�绗�199闋�绗�200闋�绗�201闋�绗�202闋�绗�203闋�绗�204闋�绗�205闋�绗�206闋�绗�207闋�绗�208闋�绗�209闋�绗�210闋�绗�211闋�绗�212闋�绗�213闋�绗�214闋�绗�215闋�绗�216闋�绗�217闋�绗�218闋�绗�219闋�绗�220闋�绗�221闋�绗�222闋�绗�223闋�绗�224闋�绗�225闋�绗�226闋�绗�227闋�绗�228闋�绗�229闋�绗�230闋�绗�231闋�绗�232闋�绗�233闋�绗�234闋�绗�235闋�绗�236闋�绗�237闋�绗�238闋�绗�239闋�绗�240闋�绗�241闋�绗�242闋�绗�243闋�绗�244闋�绗�245闋�绗�246闋�绗�247闋�绗�248闋�绗�249闋�绗�250闋�绗�251闋�绗�252闋�绗�253闋�绗�254闋�绗�255闋�绗�256闋�绗�257闋�绗�258闋�绗�259闋�绗�260闋�绗�261闋�绗�262闋�绗�263闋�绗�264闋�绗�265闋�绗�266闋�绗�267闋�绗�268闋�绗�269闋�绗�270闋�绗�271闋�绗�272闋�绗�273闋�绗�274闋�绗�275闋�绗�276闋�绗�277闋�绗�278闋�绗�279闋�绗�280闋�绗�281闋�绗�282闋�绗�283闋�绗�284闋�绗�285闋�绗�286闋�绗�287闋�绗�288闋�绗�289闋�绗�290闋�绗�291闋�绗�292闋�绗�293闋�绗�294闋�绗�295闋�绗�296闋�绗�297闋�绗�298闋�绗�299闋�绗�300闋�绗�301闋�绗�302闋�绗�303闋�绗�304闋�绗�305闋�绗�306闋�绗�307闋�绗�308闋�绗�309闋�绗�310闋�绗�311闋�绗�312闋�绗�313闋�绗�314闋�绗�315闋�绗�316闋�绗�317闋�绗�318闋�绗�319闋�绗�320闋�绗�321闋�绗�322闋�
2002 Microchip Technology Inc.
Preliminary
DS30485A-page 159
PIC18FXX39
16.4.14
SLEEP OPERATION
While in SLEEP mode, the I2C module can receive
addresses or data, and when an address match or
complete byte transfer occurs, wake the processor
from SLEEP (if the MSSP interrupt is enabled).
16.4.15
EFFECT OF A RESET
A RESET disables the MSSP module and terminates
the current transfer.
16.4.16
MULTI-MASTER MODE
In Multi-Master mode, the interrupt generation on the
detection of the START and STOP conditions allows the
determination of when the bus is free. The STOP (P)
and START (S) bits are cleared from a RESET, or when
the MSSP module is disabled. Control of the I2C bus
may be taken when the P bit (SSPSTAT<4>) is set, or
the bus is IDLE, with both the S and P bits clear. When
the bus is busy, enabling the SSP interrupt will generate
the interrupt when the STOP condition occurs.
In multi-master operation, the SDA line must be moni-
tored for arbitration, to see if the signal level is the
expected output level. This check is performed in
hardware, with the result placed in the BCLIF bit.
The states where arbitration can be lost are:
Address Transfer
Data Transfer
A START Condition
A Repeated START Condition
An Acknowledge Condition
16.4.17
MULTI -MASTER COMMUNICATION,
BUS COLLISION, AND BUS
ARBITRATION
Multi-Master mode support is achieved by bus arbitra-
tion. When the master outputs address/data bits onto
the SDA pin, arbitration takes place when the master
outputs a '1' on SDA, by letting SDA float high and
another master asserts a '0'. When the SCL pin floats
high, data should be stable. If the expected data on
SDA is a '1' and the data sampled on the SDA pin = '0',
then a bus collision has taken place. The master will set
the Bus Collision Interrupt Flag BCLIF and reset the I2C
port to its IDLE state (Figure 16-25).
If a transmit was in progress when the bus collision
occurred, the transmission is halted, the BF flag is
cleared, the SDA and SCL lines are de-asserted, and
the SSPBUF can be written to. When the user services
the bus collision Interrupt Service Routine, and if the
I2C bus is free, the user can resume communication by
asserting a START condition.
If a START, Repeated START, STOP, or Acknowledge
condition was in progress when the bus collision
occurred, the condition is aborted, the SDA and SCL
lines are de-asserted, and the respective control bits in
the SSPCON2 register are cleared. When the user ser-
vices the bus collision Interrupt Service Routine, and if
the I2C bus is free, the user can resume communication
by asserting a START condition.
The master will continue to monitor the SDA and SCL
pins. If a STOP condition occurs, the SSPIF bit will be set.
A write to the SSPBUF will start the transmission of
data at the first data bit, regardless of where the
transmitter left off when the bus collision occurred.
In Multi-Master mode, the interrupt generation on the
detection of START and STOP conditions allows the
determination of when the bus is free. Control of the I2C
bus can be taken when the P bit is set in the SSPSTAT
register, or the bus is IDLE and the S and P bits are
cleared.
FIGURE 16-25:
BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE
SDA
SCL
BCLIF
SDA released
SDA line pulled low
by another source
Sample SDA. While SCL is high,
data doesn鈥檛 match what is driven
Bus collision has occurred.
Set bus collision
interrupt (BCLIF)
by the master.
by master
Data changes
while SCL = 0
鐩搁棞(gu膩n)PDF璩囨枡 |
PDF鎻忚堪 |
|---|---|
| XF2L-3025-1 | CONN FPC 30POS 0.5MM SMT |
| PIC18F4539-E/P | IC PIC MCU FLASH 12KX16 40DIP |
| XF2L-2625-1 | CONN FPC 26POS 0.5MM SMT |
| XF2L-2235-1 | CONN FPC 22POS 0.5MM SMT |
| PIC16LF77-I/ML | IC MCU FLASH 8KX14 A/D 44QFN |
鐩搁棞(gu膩n)浠ｇ悊鍟�/鎶€琛�(sh霉)鍙冩暩(sh霉) |
鍙冩暩(sh霉)鎻忚堪 |
|---|---|
| PIC18F4439-I/ML | 鍔熻兘鎻忚堪:8浣嶅井鎺у埗鍣� -MCU 12KB 640 RAM 32 I/O RoHS:鍚� 鍒堕€犲晢:Silicon Labs 鏍稿績:8051 铏曠悊鍣ㄧ郴鍒�:C8051F39x 鏁�(sh霉)鎿�(j霉)绺界窔瀵害:8 bit 鏈€澶ф檪(sh铆)閻橀牷鐜�:50 MHz 绋嬪簭瀛樺劜(ch菙)鍣ㄥぇ灏�:16 KB 鏁�(sh霉)鎿�(j霉) RAM 澶у皬:1 KB 鐗囦笂 ADC:Yes 宸ヤ綔闆绘簮闆诲:1.8 V to 3.6 V 宸ヤ綔婧害鑼冨湇:- 40 C to + 105 C 灏佽 / 绠遍珨:QFN-20 瀹夎棰�(f膿ng)鏍�:SMD/SMT |
| PIC18F4439-I/P | 鍔熻兘鎻忚堪:8浣嶅井鎺у埗鍣� -MCU 12KB 640 RAM 32 I/O RoHS:鍚� 鍒堕€犲晢:Silicon Labs 鏍稿績:8051 铏曠悊鍣ㄧ郴鍒�:C8051F39x 鏁�(sh霉)鎿�(j霉)绺界窔瀵害:8 bit 鏈€澶ф檪(sh铆)閻橀牷鐜�:50 MHz 绋嬪簭瀛樺劜(ch菙)鍣ㄥぇ灏�:16 KB 鏁�(sh霉)鎿�(j霉) RAM 澶у皬:1 KB 鐗囦笂 ADC:Yes 宸ヤ綔闆绘簮闆诲:1.8 V to 3.6 V 宸ヤ綔婧害鑼冨湇:- 40 C to + 105 C 灏佽 / 绠遍珨:QFN-20 瀹夎棰�(f膿ng)鏍�:SMD/SMT |
| PIC18F4439-I/PT | 鍔熻兘鎻忚堪:8浣嶅井鎺у埗鍣� -MCU 12KB 640 RAM 32 I/O RoHS:鍚� 鍒堕€犲晢:Silicon Labs 鏍稿績:8051 铏曠悊鍣ㄧ郴鍒�:C8051F39x 鏁�(sh霉)鎿�(j霉)绺界窔瀵害:8 bit 鏈€澶ф檪(sh铆)閻橀牷鐜�:50 MHz 绋嬪簭瀛樺劜(ch菙)鍣ㄥぇ灏�:16 KB 鏁�(sh霉)鎿�(j霉) RAM 澶у皬:1 KB 鐗囦笂 ADC:Yes 宸ヤ綔闆绘簮闆诲:1.8 V to 3.6 V 宸ヤ綔婧害鑼冨湇:- 40 C to + 105 C 灏佽 / 绠遍珨:QFN-20 瀹夎棰�(f膿ng)鏍�:SMD/SMT |
| PIC18F4439T-E/ML | 鍔熻兘鎻忚堪:8浣嶅井鎺у埗鍣� -MCU MCU CMOS 44 RoHS:鍚� 鍒堕€犲晢:Silicon Labs 鏍稿績:8051 铏曠悊鍣ㄧ郴鍒�:C8051F39x 鏁�(sh霉)鎿�(j霉)绺界窔瀵害:8 bit 鏈€澶ф檪(sh铆)閻橀牷鐜�:50 MHz 绋嬪簭瀛樺劜(ch菙)鍣ㄥぇ灏�:16 KB 鏁�(sh霉)鎿�(j霉) RAM 澶у皬:1 KB 鐗囦笂 ADC:Yes 宸ヤ綔闆绘簮闆诲:1.8 V to 3.6 V 宸ヤ綔婧害鑼冨湇:- 40 C to + 105 C 灏佽 / 绠遍珨:QFN-20 瀹夎棰�(f膿ng)鏍�:SMD/SMT |
| PIC18F4439T-E/PT | 鍔熻兘鎻忚堪:8浣嶅井鎺у埗鍣� -MCU MCU CMOS RoHS:鍚� 鍒堕€犲晢:Silicon Labs 鏍稿績:8051 铏曠悊鍣ㄧ郴鍒�:C8051F39x 鏁�(sh霉)鎿�(j霉)绺界窔瀵害:8 bit 鏈€澶ф檪(sh铆)閻橀牷鐜�:50 MHz 绋嬪簭瀛樺劜(ch菙)鍣ㄥぇ灏�:16 KB 鏁�(sh霉)鎿�(j霉) RAM 澶у皬:1 KB 鐗囦笂 ADC:Yes 宸ヤ綔闆绘簮闆诲:1.8 V to 3.6 V 宸ヤ綔婧害鑼冨湇:- 40 C to + 105 C 灏佽 / 绠遍珨:QFN-20 瀹夎棰�(f膿ng)鏍�:SMD/SMT |
鐧�(f膩)甯冪穵鎬ラ噰璩�锛�3鍒嗛悩宸﹀彸鎮ㄥ皣寰楀埌鍥炲京(f霉)銆�
