參數資料
型號: PIC16C622AT-40/SO
廠商: Microchip Technology
文件頁數: 37/89頁
文件大?。?/td> 0K
描述: IC MCU OTP 2KX14 COMP 18SOIC
標準包裝: 1,100
系列: PIC® 16C
核心處理器: PIC
芯體尺寸: 8-位
速度: 40MHz
外圍設備: 欠壓檢測/復位,POR,WDT
輸入/輸出數: 13
程序存儲器容量: 3.5KB(2K x 14)
程序存儲器類型: OTP
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 2.5 V ~ 5.5 V
振蕩器型: 外部
工作溫度: 0°C ~ 70°C
封裝/外殼: 18-SOIC(0.295",7.50mm 寬)
包裝: 帶卷 (TR)
其它名稱: PIC16C622AT40/SO
42
AT90S1200
0838H–AVR–03/02
Programming the EEPROM
The programming algorithm for the EEPROM data memory is as follows (refer to “Pro-
gramming the Flash” for details on command, address and data loading):
1.
A: Load Command “0001 0001”.
2.
C: Load Address Low Byte ($00 - $3F).
3.
D: Load Data Low Byte ($00 - $FF).
4.
E: Write Data Low Byte.
Reading the EEPROM
The algorithm for reading the EEPROM memory is as follows (refer to “Programming the
Flash” for details on command and address loading):
1.
A: Load Command “0000 0011”.
2.
C: Load Address Low Byte ($00 - $3F).
3.
Set OE to “0”, and BS to “0”. The EEPROM data byte can now be read at DATA.
4.
Set OE to “1”.
Programming the Fuse Bits
The algorithm for programming the Fuse bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
1.
A: Load Command “0100 0000”.
2.
D: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
Bit 5 = SPIEN Fuse
Bit 0 = RCEN Fuse
Bit 7 - 6, 4 - 1 = “1”. These bits are reserved and should be left unprogrammed (“1”).
3.
Give WR a t
WLWH_PFB wide negative pulse to execute the programming; tWLWH_PFB
is found in Table 17. Programming the Fuse bits does not generate any activity
on the RDY/BSY pin.
Programming the Lock Bits
The algorithm for programming the Lock bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
1.
A: Load Command “0010 0000”.
2.
D: Load Data Low Byte. Bit n = “0” programs the Lock bit.
Bit 2 = Lock Bit2
Bit 1 = Lock Bit1
Bit 7 - 3, 0 = “1”. These bits are reserved and should be left unprogrammed (“1”).
3.
E: Write Data Low Byte.
The Lock bits can only be cleared by executing Chip Erase.
Reading the Fuse and Lock
Bits
The algorithm for reading the Fuse and Lock bits is as follows (refer to “Programming
the Flash” on page 39 for details on command loading):
1.
A: Load Command “0000 0100”.
2.
Set OE to “0”, and BS to “1”. The status of Fuse and Lock bits can now be read
at DATA (“0” means programmed).
Bit 7 = Lock Bit1
Bit 6 = Lock Bit2
Bit 5 = SPIEN Fuse
Bit 0 = RCEN Fuse
3.
Set OE to “1”.
Observe especially that BS needs to be set to “1”.
相關PDF資料
PDF描述
PIC16F630-I/ST IC MCU FLASH 1KX14 EEPROM14TSSOP
PIC16CE625T-30/SS IC MCU OTP 2KX14 EE COMP 20SSOP
PIC16CE625T-30/SO IC MCU OTP 2KX14 EE COMP 18SOIC
PIC18C442T-E/PT IC MCU OTP 8KX16 A/D 44TQFP
22-15-3273 CONN FFC/FPC 27POS .100 RT ANG
相關代理商/技術參數
參數描述
PIC16C622T-04/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C622T-04/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C622T-04E/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C622T-04E/SS 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
PIC16C622T-04I/SO 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 13 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT