- 您現在的位置：買賣IC網 > PDF目錄3893 > PIC12F629-I/P (Microchip Technology)IC MCU CMOS FLASH-BASE 8BIT 8DIP PDF資料下載
參數資料
| 型號： | PIC12F629-I/P |
| 廠商： | Microchip Technology |
| 文件頁數： | 13/35頁 |
| 文件大小： | 0K |
| 描述： | IC MCU CMOS FLASH-BASE 8BIT 8DIP |
| 產品培訓模塊： | Asynchronous Stimulus 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 60 |
| 系列： | PIC® 12F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 5 |
| 程序存儲器容量： | 1.75KB（1K x 14） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 128 x 8 |
| RAM 容量： | 64 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 包裝： | 管件 |
| 產品目錄頁面： | 637 (CN2011-ZH PDF) |
| 配用： | DM163029-ND - BOARD PICDEM FOR MECHATRONICS AC124001-ND - MODULE SKT PROMATEII 8DIP/SOIC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
AT89S53
0787E–MICRO–3/06
20
Reading the Signature Bytes: The signature bytes are
read by the same procedure as a normal verification of
locations 030H and 031H, except that P3.6 and P3.7 must
be pulled to a logic low. The values returned are as follows:
(030H) = 1EH indicates manufactured by Atmel
(031H) = 53H indicates 89S53
Programming Interface
Every code byte in the Flash array can be written, and the
entire array can be erased, by using the appropriate combi-
nation of control signals. The write operation cycle is self-
timed and once initiated, will automatically time itself to
completion.
All major programming vendors offer worldwide support for
the Atmel microcontroller series. Please contact your local
programming vendor for the appropriate software revision.
Serial Downloading
The Code memory array can be programmed using the
serial SPI bus while RST is pulled to V
CC. The serial inter-
face consists of pins SCK, MOSI (input) and MISO (output).
After RST is set high, the Programming Enable instruction
needs to be executed first before program/erase operations
can be executed.
An auto-erase cycle is built into the self-timed programming
operation (in the serial mode ONLY) and there is no need
to first execute the Chip Erase instruction unless any of the
lock bits have been programmed. The Chip Erase opera-
tion turns the content of every memory location in the Code
array into FFH.
The Code memory array has an address space of 0000H to
2FFFH.
Either an external system clock is supplied at pin XTAL1 or
a crystal needs to be connected across pins XTAL1 and
XTAL2. The maximum serial clock (SCK) frequency should
be less than 1/40 of the crystal frequency. With a 24 MHz
oscillator clock, the maximum SCK frequency is 600 kHz.
Serial Programming Algorithm
To program and verify the AT89S53 in the serial program-
ming mode, the following sequence is recommended:
1.
Power-up sequence:
Apply power between VCC and GND pins.
Set RST pin to “H”.
If a crystal is not connected across pins XTAL1 and
XTAL2, apply a 3 MHz to 24 MHz clock to XTAL1 pin
and wait for at least 10 milliseconds.
2.
Enable serial programming by sending the Pro-
gramming Enable serial instruction to pin
MOSI/P1.5. The frequency of the shift clock sup-
plied at pin SCK/P1.7 needs to be less than the
CPU clock at XTAL1 divided by 40.
3.
The Code array is programmed one byte at a time
by supplying the address and data together with the
appropriate Write instruction. The selected memory
location is first automatically erased before new
data is written. The write cycle is self-timed and typ-
ically takes less than 2.5 ms at 5V.
4.
Any memory location can be verified by using the
Read instruction which returns the content at the
selected address at serial output MISO/P1.6.
5.
At the end of a programming session, RST can be
set low to commence normal operation.
Power-off sequence (if needed):
Set XTAL1 to “L” (if a crystal is not used).
Set RST to “L”.
Turn V
CC power off.
Serial Programming Instruction
The Instruction Set for Serial Programming follows a 3 byte
protocol and is shown in the following table.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12F675-I/SN | IC MCU CMOS FLSH-BASE 8BIT 8SOIC |
| PIC17LC43T-08/PT | IC MCU OTP 4KX16 PWM 44TQFP |
| PIC17LC43T-08/PQ | IC MCU OTP 4KX16 PWM 44-MQFP |
| PIC17LC43T-08/L | IC MCU OTP 4KX16 PWM 44PLCC |
| PIC17LC43T-08I/PT | IC MCU OTP 4KX16 PWM 44TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F629ISN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin FLASH-Based 8-Bit CMOS Microcontrollers |
| PIC12F629-ISN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, Flash-Based 8-Bit CMOS Microcontrollers |
| PIC12F629T-E/MD | 制造商:Microchip Technology Inc 功能描述:8BIT PIC12 RISC 1.75KB FLASH 2 - Tape and Reel |
| PIC12F629T-E/MF | 功能描述:8位微控制器 -MCU 1.75KB 64 RAM 6 I/O Ext Temp DFN8 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC12F629T-E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:8-Pin, Flash-Based 8-Bit CMOS Microcontrollers |
發(fā)布緊急采購，3分鐘左右您將得到回復。