- 您現在的位置：買賣IC網 > PDF目錄11772 > PIC12F1840-E/MF (Microchip Technology)MCU 7KB FLASH 256B RAM XLP 8DFN PDF資料下載
參數資料
| 型號： | PIC12F1840-E/MF |
| 廠商： | Microchip Technology |
| 文件頁數： | 111/122頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 7KB FLASH 256B RAM XLP 8DFN |
| 產品培訓模塊： | 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 120 |
| 系列： | PIC® XLP™ 12F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 32MHz |
| 連通性： | I²C，LIN，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 5 |
| 程序存儲器容量： | 7KB（4K x 14） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大小： | 256 x 8 |
| RAM 容量： | 256 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.3 V ~ 5.5 V |
| 數據轉換器： | A/D 4x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 8-VDFN 裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁當前第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁
2011 Microchip Technology Inc.
Preliminary
DS41441B-page 89
PIC12(L)F1840
9.0
POWER-DOWN MODE (SLEEP)
The Power-Down mode is entered by executing a
SLEEP
instruction.
Upon entering Sleep mode, the following conditions
exist:
1.
WDT will be cleared but keeps running, if
enabled for operation during Sleep.
2.
PD bit of the STATUS register is cleared.
3.
TO bit of the STATUS register is set.
4.
CPU clock is disabled.
5.
31 kHz LFINTOSC is unaffected and peripherals
that operate from it may continue operation in
Sleep.
6.
Timer1 oscillator is unaffected and peripherals
that operate from it may continue operation in
Sleep.
7.
ADC is unaffected, if the dedicated FRC clock is
selected.
8.
Capacitive Sensing oscillator is unaffected.
9.
I/O ports maintain the status they had before
SLEEP
was executed (driving high, low or high-
impedance).
10. Resets other than WDT are not affected by
Sleep mode.
Refer to individual chapters for more details on
peripheral operation during Sleep.
To minimize current consumption, the following condi-
tions should be considered:
I/O pins should not be floating
External circuitry sinking current from I/O pins
Internal circuitry sourcing current from I/O pins
Current draw from pins with internal weak pull-ups
Modules using 31 kHz LFINTOSC
Modules using Timer1 oscillator
I/O pins that are high-impedance inputs should be
pulled to VDD or VSS externally to avoid switching
currents caused by floating inputs.
Examples of internal circuitry that might be sourcing
current include modules such as the DAC and FVR
modules.
See
for more information on
these modules.
9.1
Wake-up from Sleep
The device can wake-up from Sleep through one of the
following events:
1.
External Reset input on MCLR pin, if enabled
2.
BOR Reset, if enabled
3.
POR Reset
4.
Watchdog Timer, if enabled
5.
Any external interrupt
6.
Interrupts by peripherals capable of running dur-
ing Sleep (see individual peripheral for more
information)
The first three events will cause a device Reset. The
last three events are considered a continuation of pro-
gram execution. To determine whether a device Reset
or wake-up event occurred, refer to Section 7.10
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is prefetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be enabled. Wake-up will
occur regardless of the state of the GIE bit. If the GIE
bit is disabled, the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
enabled, the device executes the instruction after the
SLEEP
instruction, the device will call the Interrupt Ser-
vice Routine. In cases where the execution of the
instruction following SLEEP is not desirable, the user
should have a NOP after the SLEEP instruction.
The WDT is cleared when the device wakes up from
Sleep, regardless of the source of wake-up.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27484E10A99SA | CONN PLUG 7POS STRAIGHT W/SCKT |
| V110B48H150B2 | CONVERTER MOD DC/DC 48V 150W |
| ADP5589ACBZ-02-R7 | IC PORT EXPANDER 19I/O 25WLSCP |
| V110B48H150B | CONVERTER MOD DC/DC 48V 150W |
| V150B3V3H100BG3 | CONVERTER MOD DC/DC 3.3V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC12F1840-I/MF | 功能描述:8位微控制器 -MCU 7KB Flash EEPROM 256b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC12F1840-I/MF | 制造商:Microchip Technology Inc 功能描述:; Controller Family/Series:PIC12F; Core |
| PIC12F1840-I/P | 功能描述:8位微控制器 -MCU 7KB Flash EEPROM 256b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC12F1840-I/PC01 | 制造商:Microchip Technology Inc 功能描述: |
| PIC12F1840-I/SN | 功能描述:8位微控制器 -MCU 7KB Flash EEPROM 256b nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。