- 您現在的位置：買賣IC網 > PDF目錄3896 > PIC10F200T-E/OT (Microchip Technology)IC PIC MCU FLASH 256X12 SOT23-6 PDF資料下載
參數資料
| 型號： | PIC10F200T-E/OT |
| 廠商： | Microchip Technology |
| 文件頁數： | 20/94頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PIC MCU FLASH 256X12 SOT23-6 |
| 產品培訓模塊： | 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 1 |
| 系列： | PIC® 10F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 4MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 3 |
| 程序存儲器容量： | 384B（256 x 12） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 16 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | SOT-23-6 |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 637 (CN2011-ZH PDF) |
| 其它名稱： | PIC10F200T-E/OTDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁
2007 Microchip Technology Inc.
DS41239D-page 25
PIC10F200/202/204/206
5.0
I/O PORT
As with any other register, the I/O register(s) can be
written and read under program control. However, read
instructions (e.g., MOVF GPIO, W) always read the I/O
pins independent of the pin’s Input/Output modes. On
Reset, all I/O ports are defined as input (inputs are at
high-impedance) since the I/O control registers are all
set.
5.1
GPIO
GPIO is an 8-bit I/O register. Only the low-order 4 bits
are used (GP<3:0>). Bits 7 through 4 are unimple-
mented and read as ‘0’s. Please note that GP3 is an
input-only pin. Pins GP0, GP1 and GP3 can be config-
ured with weak pull-ups and also for wake-up on
change. The wake-up on change and weak pull-up
functions are not pin selectable. If GP3/MCLR is config-
ured as MCLR, weak pull-up is always on and wake-up
on change for this pin is not enabled.
5.2
TRIS Registers
The Output Driver Control register is loaded with the
contents of the W register by executing the TRIS f
instruction. A ‘1’ from a TRIS register bit puts the corre-
sponding output driver in a High-Impedance mode. A
‘0’ puts the contents of the output data latch on the
selected pins, enabling the output buffer. The excep-
tions are GP3, which is input-only and the GP2/T0CKI/
COUT/FOSC4 pin, which may be controlled by various
registers. See Table 5-1.
The TRIS registers are “write-only” and are set (output
drivers disabled) upon Reset.
TABLE 5-1:
ORDER OF PRECEDENCE
FOR PIN FUNCTIONS
5.3
I/O Interfacing
The equivalent circuit for an I/O port pin is shown in
Figure 5-1. All port pins, except GP3 which is input-
only, may be used for both input and output operations.
For input operations, these ports are non-latching. Any
input must be present until read by an input instruction
(e.g., MOVF GPIO, W). The outputs are latched and
remain unchanged until the output latch is rewritten. To
use a port pin as output, the corresponding direction
control bit in TRIS must be cleared (= 0). For use as an
input, the corresponding TRIS bit must be set. Any I/O
pin (except GP3) can be programmed individually as
input or output.
FIGURE 5-1:
PIC10F200/202/204/206
EQUIVALENT CIRCUIT
FOR A SINGLE I/O PIN
Note:
A read of the ports reads the pins, not the
output data latches. That is, if an output
driver on a pin is enabled and driven high,
but the external system is holding it low, a
read of the port will indicate that the pin is
low.
Priority
GP0
GP1
GP2
GP3
1
CIN+
CIN-
FOSC4
I/MCLR
2
TRIS GPIO
COUT
—
3
—
—T0CKI
—
4
—
—TRIS GPIO
—
Data
Bus
Q
D
Q
CK
Q
D
Q
CK
P
N
WR
Port
TRIS
‘f’
Data
TRIS
RD Port
VSS
VDD
I/O
pin
W
Reg
Latch
Reset
Note 1: See Table 3-2 for buffer type.
VSS
VDD
(1)
相關PDF資料 |
PDF描述 |
|---|---|
| 006200516230000 | CONN FFC/FPC 16POS 1MM R/A SMD |
| 006200516230000+ | CONN FFC/FPC 16POS 1MM R/A SMD |
| 40FMN-BMT-A-TF | CONN FMN HSNG 40POS SNGL NOR SMD |
| 0781191309 | CONN FFC/FPC 30POS .5MM VERT SMD |
| 046214012010800+ | CONN FPC VERTICAL 0.5 MM 12POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC10F200T-I/MC | 功能描述:8位微控制器 -MCU 0.375KB Fl 16B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC10F200T-I/OT | 功能描述:8位微控制器 -MCU .375kBF 16RM 4I/O Ind Temp SOT-23 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC10F200T-I/OT | 制造商:Microchip Technology Inc 功能描述:8BIT FLASH MCU 10F200 SOT-23-6 |
| PIC10F200T-I/OT | 制造商:Microchip Technology Inc 功能描述:Microcontroller IC Number of I/Os:4 |
| PIC10F200T-I/OT | 制造商:Microchip Technology Inc 功能描述:8-BIT MICROCONTROLLER IC |
發布緊急采購，3分鐘左右您將得到回復。