
2
PS8391A 06/10/99
PI5C16862C
20-Bit, 2-Port Bus Switch
with Undershoot Protection
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012
DC Electrical Characteristics
(Over the Operating Range, T
A
= 40°C to +85°C, V
CC
= 5V ±10%)
Parameters Description
V
IH
Test Conditions
(1)
Guaranteed Logic HIGH Level
Min.
2.0
Typ.
(2)
—
Max.
—
Units
V
Input HIGH Voltage
V
IL
Input LOW Voltage
Guaranteed Logic LOW Level
–0.5
—
0.8
V
I
IH
I
IL
Input HIGH Current
V
CC
= Max., V
IN
= V
CC
V
CC
= Max., V
IN
= GND
0
≤
A, B
≤
V
CC
V
CC
= Min., I
IN
= –18mA
—
—
±1
μA
Input LOW Current
—
—
±1
μA
I
OZH
High Impedance Output Current
—
—
±1
μA
V
IK
I
OS
Clamp Diode Voltage
Short Circuit Current
(3)
—
–1.8
V
A (B) = 0V, B (A) = V
CC
100
—
—
mA
V
H
Input Hysteresis at Control Pins
Switch On Resistance
(4)
—
150
—
mV
R
ON
V
CC
= Min., V
IN
= 0.0V,
I
ON
= 48mA
V
CC
= Min., V
IN
= 2.4V,
I
ON
= 15mA
—
5.5
8
—
9
16
Storage Temperature............................................................65°C to +150°C
Ambient Temperature with Power Applied...........................40°C to +85°C
Supply Voltage to Ground Potential (Inputs & V
CC
Only) ... 0.5V to +7.0V
Supply Voltage to Ground Potential (Outputs & D/O Only). 0.5V to +7.0V
DC Input Voltage................................................................... 0.5V to +7.0V
DC Output Current ..............................................................................120mA
Power Dissipation...................................................................................0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the
device. This is a stress rating only and functional
operation of the device at these or any other condi-
tions above those indicated in the operational sec-
tions of this specification is not implied. Exposure to
absolute maximum rating conditions for extended
periods may affect reliability.
Capacitance
(T
A
= 25°C, f = 1 MHz)
Parameters
(5)
C
IN
C
OFF
C
ON
Description
Input Capacitance
A/B Capacitance, Switch Off
A/B Capacitance, Switch On
Test Conditions
V
IN
= 0V
V
IN
= 0V
V
IN
= 0V
Typ.
6
6
10
Units
pF
pF
pF
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V
CC
= 5.0V, T
A
= 25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between A and B pin at indicated current through the switch. ON resistance is determined by the
lower of the voltages on the two (A,B) pins.
5. This parameter is determined by device characterization but is not production tested.
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)