參數資料
      型號: PDU1032H-.5C5
      廠商: Data Delay Devices, Inc.
      英文描述: 5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      中文描述: 5位,經過ECL接口可編程延遲線(系列PDU1032H)
      文件頁數: 2/5頁
      文件大小: 148K
      代理商: PDU1032H-.5C5
      PDU1032H
      APPLICATION NOTES
      ADDRESS UPDATE
      The PDU1032H is a memory device. As such,
      special precautions must be taken when
      changing the delay address in order to prevent
      spurious output signals. The timing restrictions
      are shown in Figure 1.
      After the last signal edge to be delayed has
      appeared on the OUT pin, a minimum time, T
      OAX
      ,
      is required before the address lines can change.
      This time is given by the following relation:
      T
      OAX
      = max { (A
      i
      - A
      i-1
      ) * T
      INC
      , 0 }
      where A
      i-1
      and A
      i
      are the old and new address
      codes, respectively. Violation of this constraint
      may, depending on the history of the input signal,
      cause spurious signals to appear on the OUT
      pin. The possibility of spurious signals persists
      until the required T
      OAX
      has elapsed.
      A similar situation occurs when using the ENB
      signal to disable the output while IN is active. In
      this case, the unit must be held in the disabled
      state until the device is able to “clear” itself. This
      is achieved by holding the ENB signal high and
      the IN signal low for a time given by:
      T
      DISH
      = A
      i
      * T
      INC
      Violation of this constraint may, depending on the
      history of the input signal, cause spurious signals
      to appear on the OUT pin. The possibility of
      spurious signals persists until the required T
      DISH
      has elapsed.
      INPUT RESTRICTIONS
      There are three types of restrictions on input
      pulse width and period listed in the
      AC
      Characteristics
      table. The
      recommended
      conditions are those for which the delay
      tolerance specifications and monotonicity are
      guaranteed. The
      suggested
      conditions are
      those for which signals will propagate through the
      unit without significant distortion. The
      absolute
      conditions are those for which the unit will
      produce some type of output for a given input.
      When operating the unit between the
      recommended and absolute conditions, the
      delays may deviate from their values at low
      frequency. However, these deviations will
      remain constant from pulse to pulse if the input
      pulse width and period remain fixed. In other
      words, the delay of the unit exhibits frequency
      and pulse width dependence when operated
      beyond the recommended conditions. Please
      consult the technical staff at Data Delay Devices
      if your application has specific high-frequency
      requirements.
      Please note that the increment tolerances listed
      represent a design goal. Although most delay
      increments will fall within tolerance, they are not
      guaranteed throughout the address range of the
      unit. Monotonicity is, however, guaranteed over
      all addresses.
      T
      DISO
      T
      OAX
      T
      AENS
      T
      ENIS
      PW
      IN
      TD
      A
      PW
      OUT
      T
      DISH
      A4-A0
      ENB
      IN
      OUT
      Figure 1: Timing Diagram
      A
      i-1
      A
      i
      T
      AIS
      Doc #97045
      2/25/03
      DATA DELAY DEVICES, INC.
      2
      Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com
      相關PDF資料
      PDF描述
      PDU1032H-.5MC5 5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      PDU1032H-10C5 5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      PDU1032H-10MC5 5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      PDU1032H-12C5 5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      PDU1032H-12MC5 5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      相關代理商/技術參數
      參數描述
      PDU1032H-5M 制造商:DATADELAY 制造商全稱:Data Delay Devices, Inc. 功能描述:5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      PDU1032H-5MC4 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Delay Line
      PDU1032H-5MC5 制造商:DATADELAY 制造商全稱:Data Delay Devices, Inc. 功能描述:5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      PDU1032H-6 制造商:DATADELAY 制造商全稱:Data Delay Devices, Inc. 功能描述:5-BIT, ECL-INTERFACED PROGRAMMABLE DELAY LINE (SERIES PDU1032H)
      PDU1032H-6C4 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Delay Line