- 您現在的位置：買賣IC網 > PDF目錄367830 > PD-LPM-0102EP (Electronic Theatre Controls, Inc.) DSL LTU POWER MODULE: 36-72VDC INPUT, DUAL 120VDC/60mA OUTPUT PDF資料下載
參數資料
| 型號： | PD-LPM-0102EP |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | DSL LTU POWER MODULE: 36-72VDC INPUT, DUAL 120VDC/60mA OUTPUT |
| 中文描述： | 數字訂購線路立陶宛電源模塊：36 - 72VDC，所有輸入，輸出雙120VDC/60mA |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 55K |
| 代理商： | PD-LPM-0102EP |
PD-LPM-0102EP
DSL LTU POWER MODULE: 36-72V
DC
INPUT, DUAL 120V
DC
/60mA OUTPUT
PD-LPM-0102EP
NOTES
1.
Outputs Overload 1 and Overload 2 are designed to drive 1mA for an opto-coupler LED (no additional resistor is needed). High
impedance load on this terminal may develop high voltage up to 120Vdc.
Outputs Unbl. and Unbl. RTN are designed to drive 1mA for an opto-coupler LED (no additional resistor is needed). High impedance load
on this terminal may develop up to 13Vdc.
Unless otherwise stated, data refers to both Output 1 and Output 2.
Connecting a resistor, Rext, between pin 6 and 8 sets the output voltage. For output voltages of 110V, Rext = 11.5K
resistor. When left
open (Rext =
∞
), the output voltage is set to its maximum value. Setting effects both Output 1 and Output 2.
The output stage acts as a current source. When output current reaches the threshold, an overload circuit will detect 5-8V drop below the
nominal set value.
The output stage acts as a current source when it reaches the current limit level. When output voltage falls below a threshold level, the
output stage is disconnected in order to reduce heat dissipation. The unit reverts to normal operation once the overload condition is
removed. Overload condition on one output does not effect the other output.
The module is designed to meet EN55022 Class B Standard with an external EMI filter. For filter design recommendations, refer to the
PowerDsine xDSL Power Modules Application Note.
When connecting the two outputs in parallel to achieve a single 120V/120mA output, automatic recovery from overload shutdown will
occur only after the total consumed output current drops below 60mA.
2.
3.
4.
5.
6.
7.
8.
SAFETY INSTRUCTIONS
(According to UL1950, CSA C22.2 No. 950 and EN60950 requirements)
1.
For North America, input voltage (nominal 48Vdc, tolerance 36-60Vdc) must be applied by isolated DC source complying with the earthed
SELV or TNV requirements of the UL1950, Third edition.
For other countries, input voltage (nominal 48Vdc, tolerance 36-72Vdc) must be supplied by isolated DC source complying with the
earthed SELV or TNV requirements of the latest version of EN60950.
2.
DC input must be protected by UL Listed fuse rated maximum T2.5A, 250V (slow-blow 2.5A, 250V fuse).
3.
When applicable, protection from excessive voltage on the output should be tested in end-use equipment.
相關PDF資料 |
PDF描述 |
|---|---|
| PD-NPM-0305EP | DSL NTU POWER MODULE (36-130V DC INPUT, 5V DC, 3.3V DC OUTPUT) |
| PD035VX1 | TFT-LCD Module |
| PD035OX1 | This technical specification applies to 3.5inch color TFT-LCD panel PD035OX1. |
| PD035VX2 | TFT-LCD Module |
| PD035VX3 | Color TFT LCD module |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PDL-PROG-LT | 制造商:Panduit Corp 功能描述: |
| PDLR-109 | 制造商:Panduit Corp 功能描述:RIBBON |
| PDLR-113 | 制造商:Panduit Corp 功能描述:BULK IDENTIFICATION PRODUCT - Labels that come on sheets or rolls |
| PDLR-134 | 制造商:Panduit Corp 功能描述: |
| PDLR-17 | 制造商:Panduit Corp 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。