- 您現在的位置：買賣IC網 > PDF目錄367823 > PCKEL14 2.5 V/3.3 V PECL/ECL 1:5 clock distribution chip PDF資料下載
參數資料
| 型號： | PCKEL14 |
| 英文描述： | 2.5 V/3.3 V PECL/ECL 1:5 clock distribution chip |
| 中文描述： | 2.5 V/3.3 V PECL的/ ECL 1:5時鐘分配芯片 |
| 文件頁數： | 12/15頁 |
| 文件大?。?/td> | 393K |
| 代理商： | PCKEL14 |
Philips Semiconductors
PCKEL14
2.5 V/3.3 V PECL/ECL 1:5 clock distribution chip
Product data
Rev. 01 — 14 October 2002
12 of 15
9397 750 09564
Koninklijke Philips Electronics N.V. 2002. All rights reserved.
12. Soldering
12.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended.
12.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 250
°
C. The top-surface
temperature of the packages should preferable be kept below 220
°
C for thick/large
packages, and below 235
°
C small/thin packages.
12.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle
to the transport direction of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side corners.
相關PDF資料 |
PDF描述 |
|---|---|
| PCKEP14 | 2.5 V/3.3 V 1:5 differential ECL/PECL/HSTL clock driver |
| PCKV857 | 70-190 MHz differential 1:10 clock driver |
| PCL-818L | High-performance DAS card with programmable gain |
| PCL01-6 | LOW CAPACITANCE TVS ARRAY |
| PCL100 | REINIGUNG TINTE FETT OEL 100ML |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCKEL14D | 功能描述:時鐘驅動器及分配 2.5/3.3V PECL/ECL CLOCK DRIVER RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| PCKEL14D, 112 | 功能描述:時鐘驅動器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| PCKEL14D, 118 | 功能描述:時鐘驅動器及分配 RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| PCKEL14D,112 | 功能描述:時鐘驅動器及分配 2.5/3.3V PECL/ECL CLOCK DRIVER RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| PCKEL14D,118 | 功能描述:時鐘驅動器及分配 2.5/3.3V PECL/ECL 1:5 CLK DRVR RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。