- 您現在的位置：買賣IC網 > PDF目錄382382 > PCK351 (NXP Semiconductors N.V.) 1:10 clock distribution device with 3-State outputs PDF資料下載
參數資料
| 型號： | PCK351 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 1:10 clock distribution device with 3-State outputs |
| 中文描述： | 1:10時鐘分配器件3態輸出 |
| 文件頁數： | 15/17頁 |
| 文件大?。?/td> | 316K |
| 代理商： | PCK351 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁
Philips Semiconductors
PCK351
1:10 clock distribution device with 3-State outputs
Product data
Rev. 01 — 14 May 2002
15 of 17
9397 750 09791
Koninklijke Philips Electronics N.V. 2002. All rights reserved.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C. A mildly-activated flux will eliminate the
need for removal of corrosive residues in most applications.
12.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low
voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time
must be limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 to 5 seconds between 270 and 320
°
C.
12.5 Package related soldering information
[1]
For more detailed information on the BGA packages refer to the (LF)BGA Application Note
(AN01026); order a copy from your Philips Semiconductors sales office.
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal
or external package cracks may occur due to vaporization of the moisture in them (the so called
popcorn effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated
Circuit Packages; Section: Packing Methods
These packages are not suitable for wave soldering. On versions with the heatsink on the bottom
side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with
the heatsink on the top side, the solder might be deposited on the heatsink surface.
If wave soldering is considered, then the package must be placed at a 45
°
angle to the solder wave
direction. The package footprint must incorporate solder thieves downstream and at the side corners.
Wave soldering is suitable for LQFP, QFP and TQFP packages with a pitch (e) larger than 0.8 mm; it
is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm.
Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than
0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
[2]
[3]
[4]
[5]
[6]
13. Revision history
Table 10:
Suitability of surface mount IC packages for wave and reflow soldering
methods
Soldering method
Wave
BGA, LBGA, LFBGA, SQFP, TFBGA, VFBGA
HBCC, HBGA, HLQFP, HSQFP, HSOP,
HTQFP, HTSSOP, HVQFN, HVSON, SMS
PLCC
[4]
, SO, SOJ
LQFP, QFP, TQFP
SSOP, TSSOP, VSO
Package
[1]
Reflow
[2]
suitable
suitable
not suitable
not suitable
[3]
suitable
not recommended
[4][5]
not recommended
[6]
suitable
suitable
suitable
Table 11:
Rev Date
01
Revision history
CPCN
20020514
Description
Product data; initial version. Engineering Change Notice 853-2344 28198.
-
相關PDF資料 |
PDF描述 |
|---|---|
| PCK351D | 1:10 clock distribution device with 3-State outputs |
| PCK3807A | 1:10 LVTTL clock distribution device |
| PCK3807AD | 1:10 LVTTL clock distribution device |
| PCK3807ADB | 1:10 LVTTL clock distribution device |
| PCK3807ADS | 1:10 LVTTL clock distribution device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCK351D | 功能描述:時鐘緩沖器 1:10 CLK DISTR DEV 3-ST OUTPUT RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| PCK351D,112 | 功能描述:時鐘緩沖器 1:10 CLK DISTR DEV RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| PCK351D,118 | 功能描述:時鐘緩沖器 1:10 CLK DISTR DEV RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| PCK351DB | 功能描述:時鐘緩沖器 1:10 CLK DISTR DEV 3-ST OUTPUT RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
| PCK351DB,112 | 功能描述:時鐘緩沖器 1:10 CLK DISTR DEV RoHS:否 制造商:Texas Instruments 輸出端數量:5 最大輸入頻率:40 MHz 傳播延遲（最大值）: 電源電壓-最大:3.45 V 電源電壓-最小:2.375 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LLP-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。