- 您現在的位置：買賣IC網 > PDF目錄367822 > PCIB40 PC(ISA)BUS I/O CARD PDF資料下載
參數資料
| 型號： | PCIB40 |
| 英文描述： | PC(ISA)BUS I/O CARD |
| 中文描述： | 電腦（ISA）總線的I / O卡 |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 284K |
| 代理商： | PCIB40 |
4
J206 PCIB40 Technical Manual
2192-09066-000-000
Operation
Reading or Writing to the Board
Control of the PCIB40 is achieved by writing to a
pointer register
and then accessing a
data
register
to read or write the required I/O register. The pointer register need only be written with a
new value if a different register is to be accessed. The board occupies only two bytes of PCbus
I/O space. Each time the board is accessed, the red LED will flash momentarily.
Digital I/O channels
To use a digital channel (or bit) as an output simply write to that channel (or bit). To use a digital
channel (or bit) as an input write a ‘1’ to the channel to initialise . Thereafter a read can be used.
You can configure each digital channel (or bit) as an input or an output but it is advisable to
configure the board in groups. e.g. Group 1,2 & 3 output, Group 4 & 5 input. When an output is set
to ‘0’ (logic low) it is not advisable to attempt to drive the external connection to logic high.
Reading a digital channel, when it is an output, will return the state of the output. This can be useful
if you need to check the status of an output.
Electrical configuration of each digital channel:
Power-up or reset state of outputs
When digital I/O boards are used to control large or crucial items of plant, it is often necessary to
define how the output lines power-up. This is because it can take many seconds to boot an
operating System and run an application program from reset and begin initialising the system.
Each
group of eight
I/O signals can be selected to be a logical ‘0’, a logical ‘1’ or ‘don’t care’ at
power-up or on reset. This is configured using jumpers (see links section).
To use this feature set the links for the power-up or reset condition required. Then in your code
write to the group registers the output levels required, and finally enable the outputs by writing a
‘1’ to bit 0 of register 90 (hex).
Note:
This feature is suited to outputs not inputs. Setting an input to a power-up state of ‘0’ will
require the group register being written with all ‘1’s’ to enable the use of the channels as inputs.
ReadStatus
WriteControl
Data
Power-UpState
A
B
FromoutputEnablelatch
Enable
D
Q
+5V
4K7
10K
I/OSignal
OutputEnableSoftware/Always
(Commonto8 I/OChannels).
A
B
(Common to 8 I/O Channels).
相關PDF資料 |
PDF描述 |
|---|---|
| PCICLOCKGEN_R001 | AMD Alchemy? Solutions Au1500? PCI Clock Generation? |
| PCK2000 | CK97 (66/100MHz) System Clock Generator(CK97 (66/100MHz) 系統時鐘發生器) |
| PCK2000DL | CK97 66/100MHz System Clock Generator |
| PCK2001M | 14.318-150 MHz IIC 1:10 clock buffer(14.318-150 MHz IIC 1:10時鐘緩沖器) |
| PCK2001R | 14.318-133 MHz I2C 1:6 Clock Buffer(14.318-133 MHz I2C 1:6時鐘緩沖器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCIC16W7M400C1 | 制造商:Positronic Industries 功能描述: |
| PCI-C588 | 功能描述:界面模塊 8 PORT ASYNC SERIAL COMM PCI CARD RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| PCI-C6600S4-2-67-167 | 制造商:Johnson Components 功能描述:SBC;DSP, 2 C9701, 2MB SRAM, IN |
| PCI-COM2 | 制造商:BCM Advanced Research 功能描述:2 PORT COM CARD - Bulk |
| PCI-COM4 | 制造商:BCM Advanced Research 功能描述:4 COM PORTS SERIAL CARD SUPPORTS 4 RX232/422/485 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。