- 您現在的位置：買賣IC網 > PDF目錄3778 > PCF8575TS/1,118 (NXP Semiconductors)IC I/O EXPANDER I2C 16B 24SSOP PDF資料下載
參數資料
| 型號： | PCF8575TS/1,118 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 23/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 24SSOP |
| 產品培訓模塊： | I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 1 |
| 接口： | I²C |
| 輸入/輸出數： | 16 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 24-SSOP |
| 包裝： | 標準包裝 |
| 包括： | POR |
| 產品目錄頁面： | 827 (CN2011-ZH PDF) |
| 其它名稱： | 568-1079-6 |
1999 Apr 07
8
Philips Semiconductors
Product specication
Remote 16-bit I/O expander for I2C-bus
PCF8575
7
FUNCTIONAL DESCRIPTION
7.1
Quasi-bidirectional I/Os
The PCF8575’s 16 ports (see Fig.7) are entirely independent and can be used either as input or output ports. Input data
is transferred from the ports to the microcontroller in the READ mode (see Fig.10). Output data is transmitted to the ports
in the WRITE mode (see Fig.9).
This quasi-bidirectional I/O can be used as an input or output without the use of a control signal for data direction.
At power-on the I/Os are HIGH. In this mode only a current source (IOH) to VDD is active. An additional strong pull-up to
VDD (IOHt) allows fast rising edges into heavily loaded outputs. These devices turn on when an output is written HIGH,
and are switched off by the negative edge of SCL. The I/Os should be HIGH before being used as inputs. After power-on
as all the I/Os are set HIGH all of them can be used as input. Any change in setting of the I/Os as either inputs or outputs
can be done with the write mode. Warning: If a HIGH is applied to an I/O which has been written earlier to LOW, a large
current (IOL) will flow to VSS. (see Characteristics note 3).
7.2
Addressing
Figures 8, 9 and 10 show the address and timing diagrams. Before any data is transmitted or received the master must
send the address of the receiver via the SDA line. The first byte transmitted after the START condition carries the address
of the slave device and the read/write bit. The address of the slave device must not be changed between the START and
the STOP conditions. The PCF8575 acts as a slave receiver or a slave transmitter.
Fig.7 Simplified schematic diagram of each I/O.
dbook, full pagewidth
MGL540
DQ
CI
S
FF
D
IOH
IOL
IOHt
Q
S
FF
100
A
to interrupt
logic
VSS
VDD
P00 to P07
P10 to 17
write pulse
data from
shift register
power-on
reset
read pulse
data to
shift register
Fig.8 Byte containing the slave address and the R/W bits.
MGL541
handbook, halfpage
S
0
1
0
A2
A1
A0 R/W
A
slave address
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9539D,118 | IC I/O EXPANDER I2C 16B 24SOIC |
| PCA9555DB,118 | IC I/O EXPANDER I2C 16B 24SSOP |
| ATTINY13A-SFR | IC MCU AVR 1K FLASH 8SOIC |
| PCA9539PW,118 | IC I/O EXPANDER I2C 16B 24TSSOP |
| ATTINY13A-MUR | MCU AVR 1KB FLASH 20MHZ 20QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8575TSDB | 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 24-Pin SSOP Tube |
| PCF8575TSDB-T | 制造商:NXP Semiconductors 功能描述: |
| PCF8576 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
| PCF8576_01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
| PCF8576C | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
發布緊急采購，3分鐘左右您將得到回復。