- 您現在的位置：買賣IC網 > PDF目錄367819 > PCF8524P I2C Serial EEPROM PDF資料下載
參數資料
| 型號： | PCF8524P |
| 英文描述： | I2C Serial EEPROM |
| 中文描述： | I2C串行EEPROM的 |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 179K |
| 代理商： | PCF8524P |
1997 Feb 13
7
Philips Semiconductors
Product specification
256 to 1024
×
8-bit CMOS EEPROMs with
I
2
C-bus interface
PCF85xxC-2 family
8
I
2
C-BUS PROTOCOL
The I
2
C-bus is for 2-way, 2-line communication between
different ICs or modules. The serial bus consists of two
bidirectional lines: one for data signals (SDA), and one for
clock signals (SCL).
Both the SDA and SCL lines must be connected to a
positive supply voltage via a pull-up resistor.
The following protocol has been defined:
Data transfer may be initiated only when the bus is not
busy.
During data transfer, the data line must remain stable
whenever the clock line is HIGH. Changes in the data
line while the clock line is HIGH will be interpreted as
control signals.
8.1
Bus conditions
The following bus conditions have been defined:
Bus not busy
: both data and clock lines remain HIGH.
Start data transfer
: a change in the state of the data
line, from HIGH-to-LOW, while the clock is HIGH,
defines the START condition.
Stop data transfer
: a change in the state of the data
line, from LOW-to-HIGH, while the clock is HIGH,
defines the STOP condition.
Data valid
: the state of the data line represents valid
data when, after a START condition, the data line is
stable for the duration of the HIGH period of the clock
signal. There is one clock pulse per bit of data.
8.2
Data transfer
Each data transfer is initiated with a START condition and
terminated with a STOP condition. The number of the data
bytes, transferred between the START and STOP
conditions is limited to 7 bytes in the E/W mode and
8 bytes in the page E/W mode.
Data transfer is unlimited in the read mode.
The information is transmitted in bytes and each receiver
acknowledges with a ninth bit.
Within the I
2
C-bus specifications a low-speed mode (2 kHz
clock rate) and a high speed mode (100 kHz clock rate)
are defined. The PCF85xxC-2 operates in both modes.
By definition a device that sends a signal is called a
‘transmitter’, and the device which receives the signal is
called a ‘receiver’. The device which controls the signal is
called the ‘master’. The devices that are controlled by the
master are called ‘slaves’.
Each byte is followed by one acknowledge bit. This
acknowledge bit is a HIGH level, put on the bus by the
transmitter. The master generates an extra acknowledge
related clock pulse. The slave receiver which is addressed
is obliged to generate an acknowledge after the reception
of each byte.
The master receiver must generate an acknowledge after
the reception of each byte that has been clocked out of the
slave transmitter.
The device that acknowledges has to pull down the SDA
line during the acknowledge clock pulse in such a way that
the SDA line is stable LOW during the HIGH period of the
acknowledge related clock pulse.
Set-up and hold times must be taken into account.
A master receiver must signal an end of data to the slave
transmitter by not generating an acknowledge on the last
byte that has been clocked out of the slave. In this event
the transmitter must leave the data line HIGH to enable the
master generation of the STOP condition.
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8531U | LCD Display Driver |
| PCF8566PN | LCD Display Driver |
| PCF8566TD | LCD Display Driver |
| PCF8566TD-T | LCD Display Driver |
| PCF8570PN | Serial SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF85263AT/AJ | 功能描述:Real Time Clock (RTC) IC Clock/Calendar I2C, 2-Wire Serial 8-SOIC (0.154", 3.90mm Width) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:時鐘/日歷 特性:警報器，閏年，監視計時器 存儲容量:- 時間格式:HH：MM：SS：hh（12/24 小時） 日期格式:YY-MM-DD-dd 接口:I2C，2 線串口 電壓 - 電源:0.9 V ~ 5.5 V 電壓 - 電源，電池:0.9 V ~ 5.5 V 電流 - 計時（最大）:0.885μA @ 3.3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SO 標準包裝:1 |
| PCF85263ATL/AX | 功能描述:Real Time Clock (RTC) IC Clock/Calendar I2C, 2-Wire Serial 10-XFDFN Exposed Pad 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:時鐘/日歷 特性:警報器，閏年，監視計時器 存儲容量:- 時間格式:HH：MM：SS：hh（12/24 小時） 日期格式:YY-MM-DD-dd 接口:I2C，2 線串口 電壓 - 電源:0.9 V ~ 5.5 V 電壓 - 電源，電池:0.9 V ~ 5.5 V 電流 - 計時（最大）:0.885μA @ 3.3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-XFDFN 裸露焊盤 供應商器件封裝:10-DFN（2.6x2.6） 標準包裝:1 |
| PCF85263ATT/AJ | 功能描述:Real Time Clock (RTC) IC Clock/Calendar I2C, 2-Wire Serial 8-TSSOP, 8-MSOP (0.118", 3.00mm Width) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:時鐘/日歷 特性:警報器，閏年，監視計時器 存儲容量:- 時間格式:HH：MM：SS：hh（12/24 小時） 日期格式:YY-MM-DD-dd 接口:I2C，2 線串口 電壓 - 電源:0.9 V ~ 5.5 V 電壓 - 電源，電池:0.9 V ~ 5.5 V 電流 - 計時（最大）:0.885μA @ 3.3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:8-TSSOP 標準包裝:1 |
| PCF85263ATT1/AJ | 功能描述:Real Time Clock (RTC) IC Clock/Calendar I2C, 2-Wire Serial 10-TFSOP, 10-MSOP (0.118", 3.00mm Width) 制造商:nxp semiconductors 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:時鐘/日歷 特性:警報器，閏年，監視計時器 存儲容量:- 時間格式:HH：MM：SS：hh（12/24 小時） 日期格式:YY-MM-DD-dd 接口:I2C，2 線串口 電壓 - 電源:0.9 V ~ 5.5 V 電壓 - 電源，電池:0.9 V ~ 5.5 V 電流 - 計時（最大）:0.885μA @ 3.3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:10-TSSOP 標準包裝:1 |
| PCF8531 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:34 x 128 pixel matrix driver |
發布緊急采購，3分鐘左右您將得到回復。