- 您現在的位置：買賣IC網 > PDF目錄367816 > PCF50603HN (NXP SEMICONDUCTORS) Controller for power supply and battery management PDF資料下載
參數資料
| 型號： | PCF50603HN |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 電源管理 |
| 英文描述： | Controller for power supply and battery management |
| 中文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQCC48 |
| 封裝： | 6 X 6 MM, 0.85 MM HEIGHT, SOT-778-1, PLASTIC, HVQFN-48 |
| 文件頁數： | 12/28頁 |
| 文件大?。?/td> | 147K |
| 代理商： | PCF50603HN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2003 Oct 31
12
Philips Semiconductors
Preliminary specification
Controller for power supply
and battery management
PCF50603
8.1.3
W
ATCHDOG TIMER
The OOC contains a WatchDog Timer (WDT). By default
it is not activated. It can be activated by setting
bit WDT_RST in the OOCC register to logic 1. Once this
bit has been set, the watchdog is enabled, and needs to be
cleared once every eight seconds. If the watchdog is not
reset in time, the PCF50603 automatically goes to the
STANDBY state when the watchdog timer expires. Status
bit WDTEXP is set when the watchdog timer expires. After
each ACTIVE to STANDBY transition the WDT is disabled
and needs to be activated again by software when
entering the ACTIVE state.
8.1.4
A
UTOMATIC RESTART AFTER BATTERY REMOVAL
The PMU allows for an automatic restart from SAVE to
ACTIVE state when the main battery is removed for a
period less than two seconds (t
BATRMLIM
). This feature is
especially convenient to avoid accidental switch-off of the
phone due to mechanical bounce on the battery. The
automatic restart is enabled or disabled by control
bit BATRM_EN in the OOCC register. By default this
automatic restart feature is disabled.
Status bit BATRMSTAT in the OOCS2 register indicates
whetherthePMUreturnedtoACTIVEstateduetoarestart
after battery removal. The status bit remains active until
the PMU returns to STANDBY or SAVE state.
Figure 6 shows the timing for an automatic restart due to
battery removal.
This feature is only triggered by battery removal
(V
BAT
< 2.7 V). All other shut-down conditions like, low
battery, high temperature, programming GO_STDBY do
not trigger this function.
This feature is only applicable upon the condition that a
BBC (V
SAVE
> V
VERY_LOW_BACK
) is available in the system.
handbook, full pagewidth
ACTIVE
ACTIVE
MCE539
SAVE
<tBATRMLIM
treset
VBAT
VLOW_BAT
VVERY_LOW_BAT
VSAVE
CLK32K
xxVDD
BATRMSTAT
(internal status bit)
VLOW_BACK
RSTHC_N
Fig.6 Automatic restart after battery removal.
相關PDF資料 |
PDF描述 |
|---|---|
| PCF50732 | Baseband and audio interface for GSM |
| PCF50732H | Baseband and audio interface for GSM |
| PCF7991AT | Advanced Basestation IC, ABIC |
| PCF80C31BH4-24H | CMOS single-chip 8-bit microcontrollers |
| PCB80C51BH-2H | CMOS single-chip 8-bit microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF50604HN/03/2C,5 | 制造商:NXP Semiconductors 功能描述:PMU FOR MOBILE PHONES - Tape and Reel |
| PCF50604HN/04/2C,5 | 制造商:NXP Semiconductors 功能描述:PMU FOR MOBILE PHONES - Tape and Reel |
| PCF50605HN/10E/N1, | 制造商:NXP Semiconductors 功能描述:PMU FOR SMARTPHONE, PDA & HDD - Tape and Reel |
| PCF50606HN/03A/N1, | 制造商:NXP Semiconductors 功能描述:PMU FOR SMARTPHONE, PDA & HDD - Tape and Reel |
| PCF50606HN/04B/N1, | 制造商:NXP Semiconductors 功能描述:PMU FOR SMARTPHONE, PDA & HDD - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。