- 您現在的位置：買賣IC網 > PDF目錄382379 > PCD3330-1 (NXP Semiconductors N.V.) Multistandard repertory dialler/ringer with EEPROM PDF資料下載
參數資料
| 型號： | PCD3330-1 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Multistandard repertory dialler/ringer with EEPROM |
| 中文描述： | 多標準匯編撥號器/帶有EEPROM鈴聲 |
| 文件頁數： | 19/32頁 |
| 文件大小： | 152K |
| 代理商： | PCD3330-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
1997 Jan 15
19
Philips Semiconductors
Product specification
Multistandard repertory dialler/ringer with
EEPROM
PCD3330-1
The 10 repertory numbers can be recalled with the
M0 to M9 keys or by pressing the MEM key followed by a
numeric digit from 0 to 9.
If the keyboard matrix contains the keys M0 to M9, each of
the 10 repertory numbers can be recalled using the
corresponding single key.
If the keyboard matrix contains the MEM key each of the
10 repertory numbers can be recalled by depressing MEM
followed by the numeric digit 0 to 9.
The maximum length of these repertory numbers is
16 or 20 digits (depending on the programmed repertory
number length) including the manually stored access
pauses.
5.6.5.1
Chain dialling
Repertory numbers can be dialled-out after or before
entering manual dialling or last number redial and by
entering the memory locations in successive order (‘chain
dialling’).
During transmission of a number recalled from the
memory location, the controller does not accept keyboard
entries. Dialling can be continued as soon as the number
under transmission is completed.
Note that the last memory location which is transmitted is
stored in the redial register.
5.6.6
3-
NUMBER REPERTORY DIALLING
When the repertory length programmed in EEPROM is set
to 16 digits, the PCD3330-1 includes also an additional
3-number repertory dialler.
These repertory numbers are only accessible with the
one-key procedure.
These 3 repertory numbers can only be recalled with the
E-1 to E-3 keys.
The maximum length of these repertory numbers is
16 digits including the manually stored access pauses.
The chain dialling procedure is equal to that explained in
10-number repertory dialling.
5.6.7
A
CCESS PAUSE STORAGE
If during entering a telephone number via keyboard for
normal dialling or during repertory number programming
the AP-key (access pause key) is pressed, then an access
pause is stored in the redial or repertory dial register.
5.6.8
M
ANUAL ACCESS PAUSES
The AP-key is used to insert an access pause during
manual dialling. It is possible to select between four
possible access pause times for each dialling mode:
For pulse dialling 1.5, 2.5, 3.0 or 6.0 s (inter-digit pause not
included).
For DTMF dialling 1.0,1.5, 3.5 or 6.0 s (inter-digit pause
not included).
5.6.9
S
TORING REPERTORY NUMBERS
When the Keytone active bit in EEPROM is HIGH, every
key activation in programming mode will result in a keytone
of 1046 Hz lasting 200 ms.
The store mode starts after going off-hook and depressing
the STO-key. With the PCD3330-1 a selection can be
made between two store modes, the ‘General’ and the
‘German’.
Repertory numbers can be stored into EEPROM via the
one-key access or the two-key access method and
following the German or General storing procedures. This
is detailed in Tables 5 and 6.
Table 5
One-key access repertory number mode (M0 to M9 and E-1 to E-3)
GENERAL PROCEDURE
GERMAN PROCEDURE
Set in operation mode
Depress STO (store key)
Telephone number
Depress STO (store key)
Location (M0 to M9/E-1 to E-3)
set in operation mode
depress STO (store key)
location (M0 to M9/E-1 to E-3)
telephone number
STO (store key)
相關PDF資料 |
PDF描述 |
|---|---|
| PCD3330-1P | Multistandard repertory dialler/ringer with EEPROM |
| PCD3330-1T | Multistandard repertory dialler/ringer with EEPROM |
| PCD3354AH | 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM |
| PCA3354CH | 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM |
| PCD3354A | 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCD3330-1D-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Pulse Telephone Dialer |
| PCD3330-1P | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard repertory dialler/ringer with EEPROM |
| PCD3330-1T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard repertory dialler/ringer with EEPROM |
| PCD3331-1P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
| PCD3331-1T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Telecommunication IC |
發(fā)布緊急采購，3分鐘左右您將得到回復。