- 您現在的位置：買賣IC網 > PDF目錄382378 > PCA9530 (NXP Semiconductors N.V.) 2-bit I2C LED dimmer PDF資料下載
參數資料
| 型號： | PCA9530 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 2-bit I2C LED dimmer |
| 中文描述： | 2位I2C LED調光 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 123K |
| 代理商： | PCA9530 |
Philips Semiconductors
Preliminary data
PCA9530
2-bit I
2
C LED dimmer
2002 Dec 12
5
POWER-ON RESET
When power is applied to V
DD
, an internal Power On Reset holds
the PCA9530 in a reset state until V
DD
has reached V
POR
. At this
point, the reset condition is released and the PCA9530 registers are
initialized to their default states, all the outputs in the off state.
EXTERNAL RESET
A reset can be accomplished by holding the RESET pin low for a
minimum of t
W
. The PCA9530 registers and I
2
C state machine will
be held in their default state until the RESET input is once again
high.
This input requires a pull-up resistor to V
DD.
CHARACTERISTICS OF THE I
2
C-BUS
The I
2
C-bus is for 2-way, 2-line communication between different ICs
or modules. The two lines are a serial data line (SDA) and a serial
clock line (SCL). Both lines must be connected to a positive supply
via a pull-up resistor when connected to the output stages of a device.
Data transfer may be initiated only when the bus is not busy.
Bit transfer
One data bit is transferred during each clock pulse. The data on the
SDA line must remain stable during the HIGH period of the clock
pulse as changes in the data line at this time will be interpreted as
control signals (see Figure 5).
SDA
SCL
SW00363
data line
stable;
data valid
change
of data
allowed
Figure 5. Bit transfer
Start and stop conditions
Both data and clock lines remain HIGH when the bus is not busy. A
HIGH-to-LOW transition of the data line, while the clock is HIGH is
defined as the start condition (S). A LOW-to-HIGH transition of the
data line while the clock is HIGH is defined as the stop condition (P)
(see Figure 6).
System configuration
A device generating a message is a transmitter: a device receiving
is the receiver. The device that controls the message is the master
and the devices which are controlled by the master are the slaves
(see Figure 7).
SDA
SCL
SW00365
S
P
SDA
SCL
START condition
STOP condition
Figure 6. Definition of start and stop conditions
MASTER
TRANSMITTER/
RECEIVER
SLAVE
RECEIVER
SLAVE
TRANSMITTER/
RECEIVER
MASTER
TRANSMITTER
MASTER
TRANSMITTER/
RECEIVER
SDA
SCL
SW00366
I
2
C
MULTIPLEXER
SLAVE
Figure 7. System configuration
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9531 | 8-bit I2C LED dimmer |
| PCA9532 | 16-bit I2C LED dimmer |
| PCA9533 | 4-bit I2C LED dimmer |
| PCA9533D01 | 4-bit I2C LED dimmer |
| PCA9533D02 | 4-bit I2C LED dimmer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9530D | 功能描述:LED照明驅動器 2-BIT I2C FM OD LED DIM RST RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9530D,112 | 功能描述:LED照明驅動器 2-BIT I2C FM OD LED RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9530D,118 | 功能描述:LED照明驅動器 2-BIT I2C FM OD LED RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| PCA9530D,118-CUT TAPE | 制造商:NXP 功能描述:PCA9530 Series 2-Bit I2C-Bus and SMBus I/O Expander LED Dimmer - SOIC - 8 |
| PCA9530DP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2-bit I2C LED dimmer |
發布緊急采購，3分鐘左右您將得到回復。