<pre id="k1hab"><menu id="k1hab"><label id="k1hab"></label></menu></pre>
  • <button id="k1hab"><input id="k1hab"></input></button><rt id="k1hab"><tr id="k1hab"><small id="k1hab"></small></tr></rt>
    參數資料
    型號: PCA80C31BH3-16WP
    廠商: NXP SEMICONDUCTORS
    元件分類: 微控制器/微處理器
    英文描述: CMOS single-chip 8-bit microcontrollers
    中文描述: 8-BIT, 16 MHz, MICROCONTROLLER, PQCC44
    文件頁數: 12/30頁
    文件大?。?/td> 411K
    代理商: PCA80C31BH3-16WP
    Philips Semiconductors
    Product specification
    80C31/80C51/87C51
    CMOS single-chip 8-bit microcontrollers
    1996 Aug 16
    12
    DC ELECTRICAL CHARACTERISTICS FOR PHILIPS NORTH AMERICA DEVICES (SC80C31 AND SC80C51)
    T
    amb
    = 0
    °
    C to +70
    °
    C or –40
    °
    C to +85
    °
    C, V
    CC
    = 5V
    ±
    10%; V
    SS
    = 0V
    SYMBOL
    PARAMETER
    TEST
    CONDITIONS
    LIMITS
    UNIT
    MIN
    TYP
    1
    MAX
    V
    IL
    Input low voltage
    4.5V < V
    CC
    < 5.5V
    –0.5
    0.2V
    CC
    –0.1
    V
    V
    IH
    Input high voltage (ports 0, 1, 2, 3, EA)
    0.2V
    CC
    +0.9
    V
    CC
    +0.5
    V
    V
    IH1
    Input high voltage, XTAL1, RST
    0.7V
    CC
    V
    CC
    +0.5
    V
    V
    OL
    Output low voltage, ports 1, 2, 3
    8
    V
    CC
    = 4.5V
    I
    OL
    2
    0.4
    V
    V
    OL1
    Output low voltage, port 0, ALE, PSEN
    8, 7
    V
    CC
    = 4.5V
    I
    OL
    2
    0.4
    V
    V
    OH
    Output high voltage, ports 1, 2, 3
    3
    V
    CC
    = 4.5V
    I
    OH
    = –30
    μ
    A
    V
    CC
    – 0.7
    V
    V
    OH1
    Output high voltage (port 0 in external bus mode),
    ALE
    9
    , PSEN
    3
    V
    CC
    = 4.5V
    I
    OH
    V
    CC
    – 0.7
    V
    I
    IL
    Logical 0 input current, ports 1, 2, 3
    V
    IN
    = 0.4V
    –1
    –50
    μ
    A
    I
    TL
    Logical 1-to-0 transition current, ports 1, 2, 3
    6
    V
    IN
    = 2.0V
    See note 4
    –650
    μ
    A
    I
    LI
    Input leakage current, port 0
    0.45 < V
    IN
    < V
    CC
    – 0.3
    ±
    10
    μ
    A
    I
    CC
    Power supply current (see Figure 8):
    Active mode @ 16MHz
    5
    Idle mode @ 16MHz
    5
    Power-down mode
    See note 5
    T
    amb
    = 0 to +70
    °
    C
    T
    amb
    = –40 to +85
    °
    C
    11.5
    1.3
    3
    32
    5
    50
    75
    μ
    A
    μ
    A
    μ
    A
    μ
    A
    R
    RST
    Internal reset pull-down resistor
    40
    225
    k
    C
    IO
    NOTES:
    1. Typical ratings are not guaranteed. The values listed are at room temperature, 5V.
    2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V
    OL
    s of ALE and ports 1 and 3. The noise is due
    to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
    worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify
    ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I
    OL
    can exceed these conditions provided that no
    single output sinks more than 5mA and no more than two outputs exceed the test conditions.
    3. Capacitive loading on ports 0 and 2 may cause the V
    OH
    on ALE and PSEN to momentarily fall below the (V
    CC
    –0.7) specification when the
    address bits are stabilizing.
    4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
    maximum value when V
    is approximately 2V.
    5. See Figures 9 through 12 for I
    CC
    test conditions.
    Active Mode:
    I
    CC
    = 1.5
    ×
    FREQ + 8.0;
    Idle Mode:
    I
    CC
    = 0.14
    ×
    FREQ +2.31; See Figure 8.
    6. This value applies to T
    amb
    = 0
    °
    C to +70
    °
    C. For T
    amb
    = –40
    °
    C to +85
    °
    C, I
    TL
    = –750
    μ
    A.
    7. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
    8. Under steady state (non-transient) conditions, I
    OL
    must be externally limited as follows:
    Maximum I
    OL
    per port pin:
    15mA (*NOTE: This is 85
    °
    C specification.)
    Maximum I
    OL
    per 8-bit port:
    26mA
    Maximum total I
    OL
    for all outputs:
    71mA
    If I
    OL
    exceeds the test condition, V
    OL
    may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
    test conditions.
    9. ALE is tested to V
    OH1
    , except when ALE is off then V
    OH
    is the voltage specification.
    10.Pin capacitance is characterized but not tested. Pin capacitance is less than 25pF. Pin capacitance of ceramic package is less than 15pF
    (except EA it is 25pF).
    Pin capacitance
    10
    (except EA)
    15
    pF
    相關PDF資料
    PDF描述
    PCF80C31BH4-24P CMOS single-chip 8-bit microcontrollers
    PCF80C31BH4-24WP CMOS single-chip 8-bit microcontrollers
    PCF80C51BH-3WP CMOS single-chip 8-bit microcontrollers
    PCA80C51BH-3WP CMOS single-chip 8-bit microcontrollers
    PCB80C51BH-4H CMOS single-chip 8-bit microcontrollers
    相關代理商/技術參數
    參數描述
    PCA80C39P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
    PCA80C39WP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
    PCA80C49WP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
    PCA80C51BH-3P 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers
    PCA80C51BH-3WP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS single-chip 8-bit microcontrollers