參數資料
型號: PCA3354CH
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM
中文描述: 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
封裝: 14 X 14 X 2.20 MM, PLASTIC, QFP-44
文件頁數: 16/32頁
文件大?。?/td> 221K
代理商: PCA3354CH
1996 Dec 18
16
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF
generator and 256 bytes EEPROM
PCA3354C; PCD3354A
From now on, it will be assumed that AD2 to AD6 will
contain the intended EEPROM page address after page
setup.
Table 17
Page setup; preset
Table 18
Page setup; auto-incrementing
7.5.2
R
EAD BYTE
Since ADDR auto-increments after a read cycle regardless
of the page boundary, successive bytes can efficiently be
read by repeating the last instruction.
Table 19
Read byte
7.5.3
W
RITE PAGE
The write cycle performs a logical OR between the data in
the EEPROM latches and that in the addressed EEPROM
page. To actually copy the data from the EEPROM
INSTRUCTION
RESULT
MOV A, #addr
MOV ADDR, A
MOV A, #data
MOV DATR, A
address of EEPROM latch
send address to ADDR
load write, erase/write or erase data
send data to addressed EEPROM
latch
INSTRUCTION
RESULT
MOV A, #MC2
MOV EPCR, A
MOV A, #baddr
increment mode control word
select increment mode
EEPROM Latch 0 address
(AD0 = AD1 = 0)
send EEPROM Latch 0 address to
ADDR
load 1
st
byte from Register 0
send 1
st
byte to EEPROM Latch 0
load 2
nd
byte from Register 1
send 2
nd
byte to EEPROM Latch 1
load 3
rd
byte from Register 2
send 3
rd
byte to EEPROM Latch 2
load 4
th
byte from Register 3
send 4
th
byte to EEPROM Latch 3
MOV ADDR, A
MOV A, R0
MOV DATR, A
MOV A, R1
MOV DATR, A
MOV A, R2
MOV DATR, A
MOV A, R3
MOV DATR, A
INSTRUCTION
RESULT
MOV A, #RDADDR
MOV ADDR, A
MOV A, DATR
load read address
send address to ADDR
read EEPROM data
latches, the corresponding bytes in the page should
previously have been erased.
The EEPROM latches are preset as described in
Section 7.5.1. The actual transfer to the EEPROM is then
performed as shown in Table 20.
The last instruction also starts Timer 2. The data in the
EEPROM latches are ORed with that in the corresponding
page bytes within 5 ms. A single-byte write is simply a
special case of ‘write page’.
ADDR auto-increments after the write cycle. If AD0 and
AD1 addressed EEPROM Latch 3 prior to the write cycle,
ADDR will point to the next EEPROM page (by bits AD2
to AD6) and to EEPROM Latch 0 (by bits AD0 and AD1).
This allows efficient coding of multi-page write operations.
Table 20
Write page
7.5.4
E
RASE
/
WRITE PAGE
The EEPROM latches are preset as described in
Section 7.5.1. The page byte corresponding to the
asserted flags (among F0 to F3) are erased and re-written
with the contents of the respective EEPROM latches.
The last instruction also starts Timer 2. Erasure takes
5 ms upon which Timer Register T2 reloads for another
5 ms cycle for writing. The top cycles together take 10 ms.
A single-byte erase/write is simply a special event of
‘erase/write page’.
ADDR auto-increments after the write cycle. If AD0 and
AD1 addressed EEPROM Latch 3 prior to the write cycle,
ADDR will point to the next EEPROM page (by AD2 to
AD6) and to EEPROM Latch 0 (by AD0 and AD1).
This allows efficient coding of multi-page erase/write
operations.
Table 21
Erase/write page
INSTRUCTION
RESULT
MOV A, #EWP + MC2
MOV EPCR, A
‘write page’ control word
start ‘write page’ cycle
INSTRUCTION
RESULT
MOV A, #EWP + MC3
MOV EPCR, A
‘erase/write page’ control word
start ‘erase/write page’ cycle
相關PDF資料
PDF描述
PCD3354A 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM
PCA3354C 8-bit microcontrollers with DTMF generator and 256 bytes EEPROM
PCD3359A 8-bit microcontroller with DTMF generator and 128 bytes EEPROM
PCD3359AH 8-bit microcontroller with DTMF generator and 128 bytes EEPROM
PCD3359AP 8-bit microcontroller with DTMF generator and 128 bytes EEPROM
相關代理商/技術參數
參數描述
PCA36-0 制造商:Panduit Corp 功能描述:B-ID
PCA36-1 制造商:Panduit Corp 功能描述:B-ID
PCA-36-2 制造商:Panduit Corp 功能描述:
PCA36-2 制造商:Panduit Corp 功能描述:
PCA36-3 制造商:Panduit Corp 功能描述: