參數資料
型號： PC2119S
廠商： NXP Semiconductors N.V.
英文描述： KPTC 18C 18#20 PIN PLUG
中文描述： LCD控制器/驅動器
文件頁數： 5/60頁
文件大?。?/td> 260K
代理商： PC2119S
1999 Mar 02
5
Philips Semiconductors
Product specification
LCD controllers/drivers
PCF2119x
6
PAD INFORMATION
The identification of each pad and its location is given in Chapter 17.
6.1
Pad functions
Table 1
Pad function description
Note
1.
When the I
2
C-bus is used, the parallel interface pad E must be at logic 0. In the I
2
C-bus read mode DB7 to DB0
should be connected to V
DD1
or left open-circuit.
a) When the parallel bus is used, pads SCL and SDA must be connected to V
SS1
or V
DD1
; they must not be left
open-circuit.
b) If the 4-bit interface is used without reading out from the PCF2119x (i.e. R/W is set permanently to logic 0), the
unused ports DB0 to DB4 can either be set to V
SS1
or V
DD1
instead of leaving them open-circuit.
SYMBOL
DESCRIPTION
V
DD1
V
DD2
V
SS1
V
SS2
V
LCD1
V
LCD2
E
Supply voltage for all except the high voltage generator.
Supply voltage for the high voltage generator.
This is the ground pad for all except the high voltage generator.
This is the ground pad for the high voltage generator.
This input is used for the generation of the LCD bias levels.
This is the V
LCD
output pad if V
LCD
is generated internally. This pad must be connected to V
LCD1
.
The data bus clock input is set HIGH to signal the start of a read or write operation; data is clocked in
or out of the chip on the negative edge of the clock; note 1.
These are three test pads. T1 and T2 must be connected to V
SS1
; T3 is left open-circuit and is not user
accessible.
T1
T2
T3
R1 to R18;
R17DUP
C1 to C80
SCL
POR
PD
SDA
R/W
LCD row driver outputs R1 to R18; these pads output the row select waveforms to the display;
R17 and R18 drive the icons. R17 has two pads R17 and R17DUP.
LCD column driver outputs C1 to C80.
I
2
C-bus serial clock input; note 1.
External power-on reset input.
PD selects the chip power-down mode; for normal operation PD = 0.
I
2
C-bus serial data input/output; note 1.
This is the read/write input. R/W selects either the read (R/W = 1) or write (R/W = 0) operation. This
pad has an internal pull-up resistor.
The RS input selects the register to be accessed for read and write. RS = 0, selects the instruction
register for write and the busy flag and address counter for read. RS = 1, selects the data register for
both read and write. This pad has an internal pull-up resistor.
The 8-bit bidirectional data bus (3-state) transfers data between the system controller and the
PCF2119x. DB7 may be used as the busy flag, signalling that internal operations are not yet
completed. In 4-bit operations the 4 higher order lines DB7 to DB4 are used; DB3 to DB0 must be left
open-circuit. Data bus line DB3 has an alternative function (SA0), when selected this is the I
2
C-bus
address pad. Each data line has its own internal pull-up resistor; note 1.
Oscillator or external clock input. When the on-chip oscillator is used this pad must be connected to
V
DD1.
RS
DB0 to DB7
OSC
相關PDF資料
PDF描述
PC2119SU KPTC 18C 18#20 PIN PLUG
PC2119V KPT 18C 18#20 SKT PLUG
PC2119VU KPTC 23C 21#20 2#16 PIN PLUG
PC2402LRS-ANH-H (75.35 k)
PC27001 Electronic Circuit Breaker
相關代理商/技術參數
參數描述
PC2119SU 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers
PC2119SU/2 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers
PC2119V 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers
PC2119VU 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers
PC2119VU/2 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*