- 您現在的位置：買賣IC網 > PDF目錄382375 > PC2119RU (NXP Semiconductors N.V.) KPTC 15C 14#20 1#16 SKT PLUG PDF資料下載
參數資料
| 型號： | PC2119RU |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | KPTC 15C 14#20 1#16 SKT PLUG |
| 中文描述： | LCD控制器/驅動器 |
| 文件頁數： | 19/60頁 |
| 文件大?。?/td> | 260K |
| 代理商： | PC2119RU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
1999 Mar 02
19
Philips Semiconductors
Product specification
LCD controllers/drivers
PCF2119x
8
INSTRUCTIONS
Only two PCF2119x registers, the Instruction Register (IR)
and the Data Register (DR) can be directly controlled by
the MPU. Before internal operation, control information is
stored temporarily in these registers, to allow interfacing to
various types of MPUs which operate at different speeds
or to allow interface to peripheral control ICs.
The PCF2119x operation is controlled by the instructions
shown in Table 6 together with their execution time.
Details are explained in subsequent sections.
Instructions are of 4 types, those that:
1.
Designate PCF2119x functions such as display
format, data length, etc.
2.
Set internal RAM addresses
3.
Perform data transfer with internal RAM
4.
Others.
In normal use, category 3 instructions are used most
frequently. However, automatic incrementing by 1
(or decrementing by 1) of internal RAM addresses after
each data write lessens the MPU program load.
The display shift in particular can be performed
concurrently with display data write, enabling the designer
to develop systems in minimum time with maximum
programming efficiency.
During internal operation, no instructions other than the
‘read busy flag’ and ‘read address’ instructions will be
executed. Because the busy flag is set to a logic 1 while an
instruction is being executed, check to ensure it is a logic 0
before sending the next instruction or wait for the
maximum instruction execution time, as given in Table 6.
An instruction sent while the busy flag is logic 1 will not be
executed.
Table 5
Instruction set for I
2
C-bus commands
Note
1.
R/W is set together with the slave address.
CONTROL BYTE
COMMAND BYTE
I
2
C-BUS COMMANDS
Co
RS 0
0
0
0
0
0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
note 1
相關PDF資料 |
PDF描述 |
|---|---|
| PC2119S | KPTC 18C 18#20 PIN PLUG |
| PC2119SU | KPTC 18C 18#20 PIN PLUG |
| PC2119V | KPT 18C 18#20 SKT PLUG |
| PC2119VU | KPTC 23C 21#20 2#16 PIN PLUG |
| PC2402LRS-ANH-H | (75.35 k) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PC2119RU/2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
| PC2119S | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
| PC2119SU | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
| PC2119SU/2 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
| PC2119V | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LCD controllers/drivers |
發布緊急采購，3分鐘左右您將得到回復。