- 您現在的位置：買賣IC網 > PDF目錄367756 > PAK-III (Electronic Theatre Controls, Inc.) Using the PAK-III I/O Coprocessor PDF資料下載
參數資料
| 型號： | PAK-III |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Using the PAK-III I/O Coprocessor |
| 中文描述： | 利用巴基斯坦三的I / O協處理器 |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 129K |
| 代理商： | PAK-III |
and communicate with it. The only problem is, you will have to make sure not to ask the
device for data while it is processing. Most operations are quite fast, but some operations
(generating a tone, or writing to EEPROM, for example) can take a long time depending
on what parameters you specify.
If you need to disable and enable the device, you'll want to drive the Enable/Busy pin.
Using this pin allows you to share the SIN, SOUT, and CLK lines with other devices that
use a similar protocol. So to connect 5 Paks you'd only need 7 I/O lines (5 enables, 1
SIN/SOUT, and 1 CLK line). You drive the Enable/Busy pin low to disable the device. If
you don't plan to use this capability, just pull the pin high with a pull up resistor. If you
are using the Busy/Mode input (see below) you can still use a pull up resistor, or just tie
the Enable/Busy pin directly to +5V.
If you ground the Busy/Mode input at start up, the device will also use the Enable/Busy
pin to tell you when it is unavailable. It does this by driving the line low when it is not
ready. That means the host must drive the pin with an open collector output if it wants to
disable the device. If you don't need to disable the device, you can just connect the pin to
a pull up resistor and connect the Enable/Busy pin to an input on the host.
If you want to use a normal output to drive the Enable/Busy pin, but you still want a busy
indication, you can connect the Busy/Mode pin to 5V through a pull up resistor. Then the
Pak III will use the Busy/Mode pin to signify it is busy (the pin is high when busy). In
this case, the Enable/Busy pin is always an input and you can drive it normally.
One thing to note about the status returns: All of the commands will return zeros in the
top bit of the response. You can use this as a form of busy indication if you are unwilling
to use any other pins. Simply read the data pin until it is zero. This indicates that the
device is sending the response. The READX and RIO commands do not follow this
convention, but they take very little time to execute anyway (less than 4 uS).
To summarize, here are the ways you can synchronize with the Pak III:
1. Monitor the Enable/Busy line while Busy/Mode is grounded. If you bring Enable/Busy
low it indicates that the Pak III is disabled. If the Pak III brings the pin low, it means it is
engaged in operations.
2. Place a pull up resistor on the Busy/Mode pin. This will cause the Busy/Mode pin to be
high when the Pak III is busy.
3. Wait until the data pin goes low before reading responses.
Command Reference
BITREAD
Reads the logical state of the specified pin (1 or 0). This command does
not
automatically force the pin into the input state. Returns a 0 or 1 byte.
相關PDF資料 |
PDF描述 |
|---|---|
| PAK-II | 310 Ivy Glen Court |
| PAK-IV | Using the PAK-IV I/O Coprocessor |
| PAK-I | 310 Ivy Glen Court |
| PAK-VA | 310 Ivy Glen Court |
| PAK-VI | 310 Ivy Glen Court |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PAK-IV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Using the PAK-IV I/O Coprocessor |
| PAKKL-3140-01 | 制造商:Richco 功能描述:CLIP ADJ SNAP IN NAT .31-.40" |
| PAKKL-3140-19 | 功能描述:CLIP ADJ. SNAP .31-.40" RoHS:是 類別:線纜，導線 - 管理 >> 線夾和夾具 系列:KWIK KLIP 標準包裝:100 系列:TC 類型:C-夾 開口尺寸:0.79" L x 0.54" W x 0.67" H（20.1mm x 13.7mm x 17.0mm） 安裝類型:釘子 材質:聚丙烯 顏色:黑 |
| PAKKL-4756-01 | 制造商:Richco 功能描述:CLIP ADJ SNAP IN NAT .47-.56" |
| PAKKL-4756-19 | 制造商:Richco 功能描述:CLIP ADJ SNAP IN NAT .47-.56" |
發布緊急采購，3分鐘左右您將得到回復。