- 您現在的位置：買賣IC網 > PDF目錄367739 > P87LPC767 (NXP Semiconductors N.V.) Low power, low price, low pin count 20 pin microcontroller with 4-kbyte OTP and 8-bit A/D converter PDF資料下載
參數資料
| 型號： | P87LPC767 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Low power, low price, low pin count 20 pin microcontroller with 4-kbyte OTP and 8-bit A/D converter |
| 中文描述： | 低功耗，低價格，低引腳數20個4KB的OTP和8位微控制器引腳/ D轉換器 |
| 文件頁數： | 50/60頁 |
| 文件大小： | 320K |
| 代理商： | P87LPC767 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
Philips Semiconductors
Product data
87LPC767
Low power, low price, low pin count (20 pin)
microcontroller with 4-kbyte OTP and 8-bit A/D converter
2001 Aug 07
47
EPROM Characteristics
Programming of the EPROM on the 87LPC767 is accomplished with
a serial programming method. Commands, addresses, and data are
transmitted to and from the device on two pins after programming
mode is entered. Serial programming allows easy implementation of
in-circuit programming of the 87LPC767 in an application board.
The 87LPC767 contains three signature bytes that can be read and
used by an EPROM programming system to identify the device. The
signature bytes designate the device as an 87LPC767 manufactured
by Philips. The signature bytes may be read by the user program at
addresses FC30h, FC31h and FC60h with the MOVC instruction,
using the DPTR register for addressing.
A special user data area is also available for access via the MOVC
instruction at addresses FCE0h through FCFFh. This “customer
code” space is programmed in the same manner as the main code
EPROM and may be used to store a serial number, manufacturing
date, or other application information.
32-Byte Customer Code Space
A small supplemental EPROM space is reserved for use by the
customer in order to identify code revisions, store checksums, add a
serial number to each device, or any other desired use. This area
exists in the code memory space from addresses FCE0h through
FCFFh. Code execution from this space is not supported, but it may
be read as data through the use of the MOVC instruction with the
appropriate addresses. The memory may be programmed at the
same time as the rest of the code memory and UCFG bytes are
programmed.
System Configuration Bytes
A number of user configurable features of the 87LPC767 must be
defined at power up and therefore cannot be set by the program after
start of execution. Those features are configured through the use of
two EPROM bytes that are programmed in the same manner as the
EPROM program space. The contents of the two configuration bytes,
UCFG1 and UCFG2, are shown in Figures 38 and 39. The values of
these bytes may be read by the program through the use of the
MOVX instruction at the addresses shown in the figure.
BIT
UCFG1.7
SYMBOL
WDTE
FUNCTION
Watchdog timer enable. When programmed (0), disables the watchdog timer. The timer may
still be used to generate an interrupt.
Reset pin disable. When 1 disables the reset function of pin P1.5, allowing it to be used as an
input only port pin.
Port reset high. When 1, ports reset to a high state. When 0, ports reset to a low state.
Brownout voltage select. When 1, the brownout detect voltage is 2.5V. When 0, the brownout
detect voltage is 3.8V. This is described in the Power Monitoring Functions section.
Clock rate select. When 0, the CPU clock rate is divided by 2. This results in machine cycles
taking 12 CPU clocks to complete as in the standard 80C51. For full backward compatibility,
this division applies to peripheral timing as well.
CPU oscillator type select. See Oscillator section for additional information. Combinations
other than those shown below should not be used. They are reserved for future use.
Oscillator Configuration
External clock input on X1 (default setting for an unprogrammed part).
Internal RC oscillator, 6 MHz
±
25%.
Low frequency crystal, 20 kHz to 100 kHz.
Medium frequency crystal or resonator, 100 kHz to 4 MHz.
High frequency crystal or resonator, 4 MHz to 20 MHz.
UCFG1.6
RPD
UCFG1.5
UCFG1.4
PRHI
BOV
UCFG1.3
CLKR
UCFG1.2–0 FOSC2–FSOC0
FOSC2–FOSC0
1 1 1
0 1 1
0 1 0
0 0 1
0 0 0
FOSC0
SU01185
FOSC1
FOSC2
CLKR
BOV
PRHI
RPD
WDTE
0
1
2
3
4
5
6
7
UCFG1
Unprogrammed Value: FFh
Address: FD00h
Figure 38. EPROM System Configuration Byte 1 (UCFG1)
相關PDF資料 |
PDF描述 |
|---|---|
| P87LPC767HD | CONNECTOR ACCESSORY |
| P87LPC769 | Low power, low price, low pin count 20 pin microcontroller with 4 kB OTP 8-bit A/D, and DAC |
| P87LPC769HD512 | IC-SM-8-BIT MCU |
| P89C51RB2 | 80C51 8-bit Flash microcontroller family(80C51八位閃速微控制器) |
| P89C51RD2FA | 80C51 8-bit Flash microcontroller family 16KB/32KB/64KB ISP/IAP Flash with 512B/512B/1KB RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P87LPC767BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low power, low price, low pin count 20 pin microcontroller with 4-kbyte OTP and 8-bit A/D converter |
| P87LPC767BD,512 | 功能描述:8位微控制器 -MCU 80C51 4K/128 OTP ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P87LPC767BN | 制造商:NXP Semiconductors 功能描述:MCU 8-Bit 87LP 80C51 CISC 4KB EPROM 3.3V/5V 20-Pin PDIP |
| P87LPC767BN,112 | 功能描述:8位微控制器 -MCU 80C51 4K/128 OTP ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P87LPC767FD | 功能描述:8位微控制器 -MCU 4K/128 OTP LPC ADC EXT SO20 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。