參數資料
型號： P83C557E4
廠商： NXP Semiconductors N.V.
英文描述： Single-chip 8-bit microcontroller(單片8位微控制器)
中文描述： 單芯片8位微控制器（單片8位微控制器）
文件頁數： 62/72頁
文件大?。?/td> 525K
代理商： P83C557E4
Philips Semiconductors
Product specification
P83C557E4/P80C557E4/P89C557E4
Single-chip 8-bit microcontroller
1999 Mar 02
62
NOTES FOR DC ELECTRICAL CHARACTERISTICS:
1.
See Figures 55 and 57 through 59 for I
DD
test conditions.
2.
The operating supply current is measured with all output pins disconnected;
XTAL1 driven with t
r
= t
f
= 5ns; V
IL
= V
SS
+ 0.5 V; V
IH
= V
DD
– 0.5 V; XTAL2, XTAL3 not connected;
EA = RSTIN = Port 0 = EW = SCL = SDA = SELXTAL1 = V
DD
; ADEXS = XTAL4 = V
SS
.
3.
The Idle Mode supply current is measured with all output pins disconnected;
XTAL1 driven with t
= t
= 5ns; V
= V
+ 0.5 V; V
= V
– 0.5 V; XTAL2, XTAL3 not connected;
Port 0 = EW = SCL = SDA = SELXTAL 1 = V
DD
; EA = RSTIN = ADEXS = XTAL4 = V
SS
.
4.
The Power-down current is measured with all output pins disconnected;
XTAL2 not connected; Port 0 = EW = SCL = SDA = SELXTAL 1 = V
DD
; EA = RSTIN = ADEXS = XTAL1 = XTAL4 = V
SS
.
5.
The input threshold voltage of SCL and SDA (SIO1) meets the I
2
C specification, so an input voltage below 0.3 V
DD
will be recognized as a
logic 0 while an input voltage above 0.7 V
DD
will be recognized as a logic 1.
6.
Pins of ports 1, 2, 3, and 4 source a transition current when they are being externally driven from HIGH to LOW. The transition current reaches
its maximum value when V
IN
is approximately 2 V.
7.
Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V
of ALE and ports 1, 3 and 4. The noise is
due to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations.
In the worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to
qualify ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input.
8.
Capacitive loading on ports 0 and 2 may cause the V
OH
on ALE and PSEN to momentarily fall below the 0.9V
DD
specification when the address
bits are stabilizing.
9.
Conditions: AV
REF–
= 0 V; AV
DD
= 5.0 V, AV
REF+
= 5.12 V. V
DD
= 5.0 V, V
SS
= 0 V, ADC is monotonic with no missing codes. Measurement
by continuous conversion of AV
IN
= –20mV to 5.12 V in steps of 0.5mV, derivating parameters from collected conversion results of ADC.
ADC prescaler programmed according to the actual oscillator frequency, resulting in a conversion time within the specified range for t
conv
(15
μ
s ... 50
μ
s).
10. The differential non-linearity (DL
e
) is the difference between the actual step width and the ideal step width.
11. The ADC is monotonic; there are no missing codes.
12. The integral non-linearity (IL
) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset error.
13. The offset error (OS
e
) is the absolute difference between the straight line which fits the actual transfer curve (after removing gain error), and
a straight line which fits the ideal transfer curve. The offset error is constant at every point of the actual transfer curve.
14. The gain error (G
) is the relative difference in percent between the straight line fitting the actual transfer curve (after removing offset error),
and the straight line which fits the ideal transfer curve. Gain error is constant at every point on the transfer curve.
15. The absolute voltage error (A
e
) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated
ADC and the ideal transfer curve.
16. This should be considered when both analog and digital signals are simultaneously input to port 5.
17. The supply current with 32 kHz oscillator running and PLL operation (SELXTAL1 = 0) is measured with all output pins disconnected;
XTAL4 driven with t
r
= t
f
= 5ns; V
IL
= V
SS
+ 0.5 V; V
IH
= V
DD
– 0.5 V; XTAL2 not connected;
Port 0 = EW = SCL = SDA = V
DD
; EA = RSTIN = ADEXS = SELXTAL 1 = XTAL1 = V
SS
.
18. Not 100% tested; sum of A
IID
(PLL) and A
IDD
(HF-Oscillator).
19. The parameter meets the I
2
C bus specification for standard-mode and fast-mode devices.
20. Not 100% tested.
相關PDF資料
PDF描述
P80C557E4 Single-chip 8-bit microcontroller(單片8位微控制器)
P89C557E6 Single-chip 8-bit microcontroller(單片8位微控制器)
P80C557E6 Single-chip 8-bit microcontroller(單片8位微控制器)
P89C58 80C51 8-bit microcontroller family 4K/8K/16K/32K Flash
P89C54X2 80C51 8-bit Flash microcontroller family
相關代理商/技術參數
參數描述
P83C557E4EBB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller
P83C557E4EBB/YYY 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P83C557E4EFB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller
P83C557E4EFB/YYY 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
P83C557E6 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 8-bit microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*