<ins id="80uog"><label id="80uog"></label></ins>
<pre id="80uog"></pre>
<kbd id="80uog"></kbd>
<nobr id="80uog"></nobr>
  • <em id="80uog"><sup id="80uog"></sup></em>
    <ins id="80uog"></ins>
    <thead id="80uog"><tt id="80uog"></tt></thead>
    <tbody id="80uog"><dfn id="80uog"></dfn></tbody><input id="80uog"><noframes id="80uog">
    參數資料
    型號: P80C52-2
    廠商: INTEL CORP
    元件分類: 微控制器/微處理器
    英文描述: CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
    中文描述: 8-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PDIP40
    封裝: PLASTIC, DIP-40
    文件頁數: 5/23頁
    文件大?。?/td> 319K
    代理商: P80C52-2
    8XC52/54/58
    If desired, ALE operation can be disabled by setting
    bit 0 of SFR location 8EH. With this bit set, the pin is
    weakly pulled high. However, the ALE disable fea-
    ture will be suspended during a MOVX or MOVC in-
    struction, idle mode, power down mode and ICE
    mode. The ALE disable feature will be terminated by
    reset. When the ALE disable feature is suspended or
    terminated, the ALE pin will no longer be pulled up
    weakly. Setting the ALE-disable bit has no affect if
    the microcontroller is in external execution mode.
    Throughout the remainder of this data sheet, ALE
    will refer to the signal coming out of the ALE/PROG
    pin, and the pin will be referred to as the ALE/PROG
    pin.
    PSEN:
    Program Store Enable is the read strobe to
    external Program Memory.
    When the 8XC5X is executing code from external
    Program Memory, PSEN is activated twice each
    machine cycle, except that two PSEN activations
    are skipped during each access to external Data
    Memory.
    EA/V
    PP
    :
    External Access enable. EA must be
    strapped to VSS in order to enable the device to
    fetch code from external Program Memory locations
    0000H to 0FFFFH. Note, however, that if any of the
    Lock bits are programmed, EA will be internally
    latched on reset.
    EA should be strapped to V
    CC
    for internal program
    executions.
    This pin also receives the programming supply volt-
    age (V
    PP
    ) during EPROM programming.
    XTAL1:
    Input to the inverting oscillator amplifier.
    XTAL2:
    Output from the inverting oscillator amplifi-
    er.
    OSCILLATOR CHARACTERISTICS
    XTAL1 and XTAL2 are the input and output, respec-
    tively, of a inverting amplifier which can be config-
    ured for use as an on-chip oscillator, as shown in
    Figure 3. Either a quartz crystal or ceramic resonator
    may be used. More detailed information concerning
    the use of the on-chip oscillator is available in Appli-
    cation Note AP-155, ‘‘Oscillators for Microcontrol-
    lers’’, Order No. 230659.
    272336–5
    C1, C2
    e
    30 pF
    g
    10 pF for Crystals
    For Ceramic Resonators, contact resonator manufac-
    turer.
    Figure 3. Oscillator Connections
    To drive the device from an external clock source,
    XTAL1 should be driven, while XTAL2 floats, as
    shown in Figure 4. There are no requirements on the
    duty cycle of the external clock signal, since the in-
    put to the internal clocking circuitry is through a di-
    vide-by-two flip-flop, but minimum and maximum
    high and low times specified on the data sheet must
    be observed.
    An external oscillator may encounter as much as a
    100 pF load at XTAL1 when it starts up. This is due
    to interaction between the amplifier and its feedback
    capacitance. Once the external signal meets the V
    IL
    and V
    IH
    specifications the capacitance will not ex-
    ceed 20 pF.
    272336–6
    Figure 4. External Clock Drive Configuration
    IDLE MODE
    The user’s software can invoke the Idle Mode. When
    the microcontroller is in this mode, power consump-
    tion is reduced. The Special Function Registers and
    the onboard RAM retain their values during Idle, but
    the processor stops executing instructions. Idle
    Mode will be exited if the chip is reset or if an en-
    abled interrupt occurs.
    5
    相關PDF資料
    PDF描述
    P80C52-24 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
    P80C52-33 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
    P80C54 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
    P80C54-1 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
    P80C54-2 CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
    相關代理商/技術參數
    參數描述
    P80C52-20 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
    P80C52-24 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER
    P80C52-25 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
    P80C52-30 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
    P80C52-33 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:CHMOS SINGLE-CHIP 8-BIT MICROCONTROLLER