- 您現在的位置：買賣IC網 > PDF目錄367630 > P3300AA61RP SIDAC|360V V(BO) MAX|800MA I(S)|TO-220VAR PDF資料下載
參數資料
| 型號： | P3300AA61RP |
| 英文描述： | SIDAC|360V V(BO) MAX|800MA I(S)|TO-220VAR |
| 中文描述： | SIDAC的| 360V五（公報）最大| 800mA的我（縣）|對220VAR |
| 文件頁數： | 86/161頁 |
| 文件大?。?/td> | 986K |
| 代理商： | P3300AA61RP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁當前第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
ITU-T K.20 and K.21
SIDACtor
Data Book
4 - 12
Teccor Electronics
(972) 580-7777
External Protectors
For equipment being tested to the exposed level, it is standard practice for external
line protectors (typically gas tubes) to be used in order to handle the large surge
currents generated during K.20 and K.21 qualification. Realizing that these protectors
can affect the characteristics of the EUT, it is important that the protectors used be
agreed upon by the principal parties involved (the equipment supplier and testing
administrator). Once agreed upon, the protectors should be used when primary
protection is specified, and allowance should be given for a new set of protectors after
the completion of each test sequence.
Note:
An alternative to using external protectors is for the test administrator to simulate the
conditions expected (as if the external protectors were used) by modifying the surges
found in K.20 and K.21.
Equipment Boundaries
Because of the numerous types of equipment, during K.20 and K.21 testing ITU-T
looks at each EUT as a
“
black box
”
with three terminals (A, B, and E). The applicant is
expected to define the boundaries of this
“
black box
”
, and in doing so, should be aware
that any protective device within these boundaries is considered an unchangeable part
of that piece of equipment.
Permitted Malfunction or Damage
During K.20 and K.21 qualification, ITU-T recognizes two levels of malfunction or
damage to the EUT:
Level A states that equipment withstands the test without damage or disturbance
and operates properly after the test. If specifically permitted, the administration
may accept the opening of the fuse.
Level B states that a fire hazard does not occur in the equipment as a result of the
test, and that any permanent damage or malfunction is confined to a small number
of external line interface circuits (as defined by the test administrator).
The acceptable level of malfunction for each test is specified under Acceptance
Criteria.
相關PDF資料 |
PDF描述 |
|---|---|
| P3500EA | 44 PIN, 32 KB ENH FLASH, 1536 RAM, 36 I/O, -40C to +125C, 44-QFN, TUBE |
| P3500EARP1 | SIDAC|400V V(BO) MAX|800MA I(S)|TO-92VAR |
| P3500EARP2 | SIDAC|400V V(BO) MAX|800MA I(S)|TO-92VAR |
| P3500EB | SIDAC|400V V(BO) MAX|800MA I(S)|TO-92VAR |
| P3500EBRP1 | SIDAC|400V V(BO) MAX|800MA I(S)|TO-92VAR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P3301 | 制造商:TYAN 功能描述:- Bulk |
| P-3301 | 制造商:Eveready 功能描述: |
| P3-30100 | 制造商:OTTO Engineering Inc 功能描述:S/A P3-31111 WITH |
| P3-30101-1 | 制造商:OTTO Engineering Inc 功能描述:S/A P1-30075 EX. |
| P3-30101-2 | 制造商:OTTO Engineering Inc 功能描述:S/A P1-30075 EX. |
發布緊急采購，3分鐘左右您將得到回復。