參數資料
型號： ord213
廠商： OKI SEMICONDUCTOR CO., LTD.
英文描述： Reed Switch(舌簧開關)
中文描述： 干簧（舌簧開關）
文件頁數： 27/145頁
文件大?。?/td> 729K
代理商： ORD213
25
REED SWITCH
PRECAUTIONS AND APPLICATIONS
with a capacitor where large current flows
to charge the capacitor, thus requiring the
contact protection circuit. Fig. 1.3 shows
examples of protection circuits.
Figure 1.3
+E
+E
Is
R
R
R: Current limiting resistance
R should be determined to satisfy
Is < 0.5 A to 1A
R: Parallel resistance
R is put into the circuit to preheat
lamp filament and increase
the resistance. R is given by the
following.
R <Filament resistance
3
If no resistance is to be put into the circuit, use
ORD2211
1-4 Wiring capacitance
When wiring a load and reed switch over
long distance, electrostatic capacitance
arising from the cable can influence the
reed switch contact. Therefore, inductance
LS should be used. Ls value differs ac-
cording to the load current but should be
in the range of 0.5 to 5 mH.
( )
Load
Ls
Wiring
capacitance
50 m or more
2.
Reed Switch Lead Forming
When reed switches are used, usually the
leads are cut or bent. However, precau-
tions should be taken when performing
these processes.
Figure 2.2
(1) Cutting and bending positions must
be determined with reference to the
center of the contact or to the end of
the lead. If the position is measured
from the end of the glass tube, the
contact center position may be moved.
(2) When in cutting on bending the leads,
be sure to protect the sealing portions.
As shown in Figure 2.1, the lead should
be placed firmly by a jig.
(3) After the process, confirm that there is
no crack or chipping in the glass tube.
Lead bending
Lead cutting
Fixed jig
Fixed jig
Figure 2.1
2-1 Cutting the leads
Since the leads of a reed switch comprise
part of the magnetic circuit, shortening
the leads by cutting will cause the re-
quired ampere turns for pull-in and drop-
out to increase as shown in Fig. 2.2. Here
in this figure, a standard coil was used in
making measurements and there may be
differences when the reed switch is driven
by a permanent magnet depending on the
difference of the shape of magnet and
orientation of magnetization. Therefore,
it is necessary to actually examine the
change of the pull-in and drop-out values
by the magnet and drive method to be
used.
LEAD CUTTING LENGTH
1
+
2
mm
C
20
15
10
5
0
4
8
12
16
20
ORD234
ORD225
相關PDF資料
PDF描述
ord219 Reed Switch(舌簧開關)
ord234 Reed Switch(舌簧開關)
ORT82G5 ORCA ORT82G5 1.0.1-25/2.0-2.5/3.125 Gbits/s Backplane Interface FPSC
ORT8850 Field-Programmable System Chip (FPSC) Eight-Channel x 850 Mbits/s Backplane Transceiver
ORT8850H Field-Programmable System Chip (FPSC) Eight-Channel x 850 Mbits/s Backplane Transceiver
相關代理商/技術參數
參數描述
ORD213/10-15 AT 功能描述:磁性/簧片開關 1 Form A 7mm AT 1015 OKI RoHS:否 制造商:MEDER electronic (Standex) 開關類型:Reed 觸點形式:1 Form A (SPST-NO) 觸點額定值:10 VA 操作范圍:10 At to 50 At 工作間隙: 磁鐵類型: 顏色: 端接類型:Axial 封裝:Bulk
ORD213/15-20 AT 功能描述:磁性/簧片開關 1 Form A 7mm AT 1520 OKI RoHS:否 制造商:MEDER electronic (Standex) 開關類型:Reed 觸點形式:1 Form A (SPST-NO) 觸點額定值:10 VA 操作范圍:10 At to 50 At 工作間隙: 磁鐵類型: 顏色: 端接類型:Axial 封裝:Bulk
ORD213/20-30 AT 功能描述:磁性/簧片開關 1 Form A 7mm AT 2030 RoHS:否 制造商:MEDER electronic (Standex) 開關類型:Reed 觸點形式:1 Form A (SPST-NO) 觸點額定值:10 VA 操作范圍:10 At to 50 At 工作間隙: 磁鐵類型: 顏色: 端接類型:Axial 封裝:Bulk
ORD213-1015 功能描述:磁性/簧片開關 Reed Switch, 1 Form A, SPST-NO, 7mm AT 1015 OKI RoHS:否 制造商:MEDER electronic (Standex) 開關類型:Reed 觸點形式:1 Form A (SPST-NO) 觸點額定值:10 VA 操作范圍:10 At to 50 At 工作間隙: 磁鐵類型: 顏色: 端接類型:Axial 封裝:Bulk
ORD213-1520 功能描述:磁性/簧片開關 Reed Switch, 1 Form A, SPST-NO, 7mm AT 1520 OKI RoHS:否 制造商:MEDER electronic (Standex) 開關類型:Reed 觸點形式:1 Form A (SPST-NO) 觸點額定值:10 VA 操作范圍:10 At to 50 At 工作間隙: 磁鐵類型: 顏色: 端接類型:Axial 封裝:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*