- 您現在的位置：買賣IC網 > PDF目錄384795 > OPA4227UA2K5G4 (Texas Instruments, Inc.) High Precision, Low Noise OPERATIONAL AMPLIFIERS PDF資料下載
參數資料
| 型號： | OPA4227UA2K5G4 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | High Precision, Low Noise OPERATIONAL AMPLIFIERS |
| 中文描述： | 高精度，低噪聲運算放大器 |
| 文件頁數： | 12/27頁 |
| 文件大?。?/td> | 847K |
| 代理商： | OPA4227UA2K5G4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
OPA227, 2227, 4227
OPA228, 2228, 4228
12
SBOS110A
www.ti.com
INPUT BIAS CURRENT CANCELLATION
The input bias current of the OPA227 and OPA228 series is
internally compensated with an equal and opposite cancella-
tion current. The resulting input bias current is the difference
between with input bias current and the cancellation current.
The residual input bias current can be positive or negative.
When the bias current is cancelled in this manner, the input
bias current and input offset current are approximately equal.
A resistor added to cancel the effect of the input bias current
(as shown in Figure 3) may actually increase offset and noise
and is therefore not recommended.
Design of low noise op amp circuits requires careful
consideration of a variety of possible noise contributors:
noise from the signal source, noise generated in the op
amp, and noise from the feedback network resistors. The
total noise of the circuit is the root-sum-square combina-
tion of all noise components.
The resistive portion of the source impedance produces
thermal noise proportional to the square root of the
resistance. This function is shown plotted in Figure 4.
Since the source impedance is usually fixed, select the op
amp and the feedback resistors to minimize their contri-
bution to the total noise.
Figure 4 shows total noise for varying source imped-
ances with the op amp in a unity-gain configuration (no
feedback resistor network and therefore no additional
noise contributions). The operational amplifier itself con-
tributes both a voltage noise component and a current
FIGURE 3. Input Bias Current Cancellation.
FIGURE 4. Noise Performance of the OPA227 in Unity-
Gain Buffer Configuration.
NOISE PERFORMANCE
Figure 4 shows total circuit noise for varying source imped-
ances with the op amp in a unity-gain configuration (no
feedback resistor network, therefore no additional noise con-
tributions). Two different op amps are shown with total circuit
noise calculated. The OPA227 has very low voltage noise,
making it ideal for low source impedances (less than 20k
).
A similar precision op amp, the OPA277, has somewhat higher
voltage noise but lower current noise. It provides excellent
noise performance at moderate source impedance (10k
to
100k
). Above 100k
, a FET-input op amp such as the
OPA132 (very low current noise) may provide improved
performance. The equation is shown for the calculation of the
total circuit noise. Note that e
n
= voltage noise, i
n
= current
noise, R
S
= source impedance, k = Boltzmann’s constant =
1.38 10
–23
J/K and T is temperature in K. For more details on
calculating noise, see the insert titled “Basic Noise Calcula-
tions.”
noise component. The voltage noise is commonly mod-
eled as a time-varying component of the offset voltage.
The current noise is modeled as the time-varying compo-
nent of the input bias current and reacts with the source
resistance to create a voltage component of noise. Conse-
quently, the lowest noise op amp for a given application
depends on the source impedance. For low source imped-
ance, current noise is negligible and voltage noise gener-
ally dominates. For high source impedance, current noise
may dominate.
Figure 5 shows both inverting and noninverting op amp
circuit configurations with gain. In circuit configurations
with gain, the feedback network resistors also contribute
noise. The current noise of the op amp reacts with the
feedback resistors to create additional noise components.
The feedback resistor values can generally be chosen to
make these noise sources negligible. The equations for
total noise are shown for both configurations.
BASIC NOISE CALCULATIONS
Op Amp
R
1
R
2
R
B
= R
2
|| R
1
External Cancellation Resistor
Not recommended
for OPA227
Conventional Op Amp Configuration
Recommended OPA227 Configuration
OPA227
R
1
R
2
No cancellation resistor.
See text.
VOLTAGE NOISE SPECTRAL DENSITY
vs SOURCE RESISTANCE
100k
10M
Source Resistance, R
S
(
)
100
1k
10k
1.00+03
1.00E+02
1.00E+01
1.00E+00
0
T
√
H
OPA227
OPA277
Resistor Noise
Resistor Noise
OPA277
OPA227
R
S
E
O
E
O
2
= e
n
2
+ (i
n
R
S
)
2
+ 4kTR
S
相關PDF資料 |
PDF描述 |
|---|---|
| OPA4228UA2K5 | High Precision, Low Noise OPERATIONAL AMPLIFIERS |
| OPA348AI | 1MHz, 45レA, CMOS, Rail-to-Rail OPERATIONAL AMPLIFIERS |
| OPA2348AI | 1MHz, 45レA, CMOS, Rail-to-Rail OPERATIONAL AMPLIFIERS |
| OPA4348AI | 1MHz, 45レA, CMOS, Rail-to-Rail OPERATIONAL AMPLIFIERS |
| OPA4363 | 1.8V, 7MHz, 90dB CMRR, SINGLE-SUPPLY, RAIL-TO-RAIL I/O OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA4227UAG4 | 功能描述:運算放大器 - 運放 High Prec Low Noise Oper Amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA4228 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:High Precision, Low Noise OPERATIONAL AMPLIFIERS |
| OPA4228PA | 功能描述:運算放大器 - 運放 High Prec Low Noise Oper Amplifier RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA4228PA | 制造商:BURR-BROWN 功能描述:OP AMP QUAD LOW NOISE 4228 DIP14 |
| OPA4228PAG4 | 功能描述:運算放大器 - 運放 Hi Precision Low Noise Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。