參數資料
型號: OPA121KU
英文描述: Low Cost Precision Difet OPERATIONAL AMPLIFIER
中文描述: 低成本精密Difet運算放大器
文件頁數: 6/6頁
文件大?。?/td> 91K
代理商: OPA121KU
OPA121
6
–10
–5
0
+5
+10
–20
–10
0
10
20
30
40
50
60
70
80
I
LF155
AD547
OPA121
OP-15/16/17 "Perfect Bias Current Cancellation"
LF156/157
AD547
LF155
OPA121
LF156/157
T = +25°C; curves taken from
mfg. published typical data
Common-Mode Voltage (VDC)
this may cause a noticeable degradation of offset voltage and
drift.
Static protection is recommended when handling any
precision IC operational amplifier.
GUARDING AND SHIELDING
As in any situation where high impedances are involved,
careful shielding is required to reduce “hum” pickup in input
leads. If large feedback resistors are used, they should also
be shielded along with the external input circuitry.
Leakage currents across printed circuit boards can easily
exceed the bias current of the OPA121. To avoid leakage
problems, it is recommended that the signal input lead of the
OPA121 be wired to a Teflon standoff. If the OPA121 is
to be soldered directly into a printed circuit board, utmost
care must be used in planning the board layout. A “guard”
pattern should completely surround the high-impedance in-
put leads and should be connected to a low-impedance point
which is at the signal input potential.
The amplifier case should be connected to any input shield
or guard via pin 8. This insures that the amplifier itself is
fully surrounded by guard potential, minimizing both leak-
age and noise pickup (see Figure #2).
If guarding is not required, pin 8 (case) should be connected
to ground.
BIAS CURRENT CHANGE
VERSUS COMMON-MODE VOLTAGE
The input bias currents of most popular BIFET operational
amplifiers are affected by common-mode voltage (Figure 3).
Higher input FET gate-to-drain voltage causes leakage and
ionization (bias) currents to increase. Due to its cascode
input stage, the extremely-low bias current of the OPA121
is not compromised by common-mode voltage.
FIGURE 2. Connection of Input Guard.
7
6
8
TO-99 Bottom View
3
OPA121
2
8
6
In
Out
Non-Inverting
3
OPA121
2
8
6
In
Out
Buffer
3
OPA121
2
8
6
In
Out
Inverting
3
2
4
5
6
7
8
1
Mini-DIP Bottom View
3
2
4
1
5
BOARD LAYOUT
FOR INPUT GUARDING
Guard top and bottom of board.
Alternate: use Teflon standoff
for sensitive input pins.
FIGURE 3. Input Bias Current vs Common-Mode Voltage.
Teflon E.I. du Pont de Nemours & Co.
相關PDF資料
PDF描述
OPA124 Low Noise Precision Difet OPERATIONAL AMPLIFIER
OPA124P Low Noise Precision Difet OPERATIONAL AMPLIFIER
OPA124PA Low Noise Precision Difet OPERATIONAL AMPLIFIER
OPA124PB Low Noise Precision Difet OPERATIONAL AMPLIFIER
OPA124U Low Noise Precision Difet OPERATIONAL AMPLIFIER
相關代理商/技術參數
參數描述
OPA121KU/2K5 功能描述:運算放大器 - 運放 Lo Cost Prec Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
OPA121KU/2K5E4 功能描述:運算放大器 - 運放 Lo Cost Prec Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
OPA121KU/2K5G4 功能描述:運算放大器 - 運放 Lo Cost Prec Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
OPA121KUE4 功能描述:運算放大器 - 運放 Lo Cost Prec Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
OPA124 制造商:BB 制造商全稱:BB 功能描述:Low Noise Precision Difet OPERATIONAL AMPLIFIER