參數資料
型號: OPA111
英文描述: Low Noise Precision Difet OPERATIONAL AMPLIFIER
中文描述: 低噪聲運算放大器精密Difet
文件頁數: 9/12頁
文件大?。?/td> 178K
代理商: OPA111
9
OPA111
should completely surround the high impedance input leads
and should be connected to a low impedance point which is
at the signal input potential.
The amplifier case should be connected to any input shield
or guard via pin 8. This insures that the amplifier itself is
fully surrounded by guard potential, minimizing both leak-
age and noise pickup (see Figure 3).
If guarding is not required, pin 8 (case) should be connected
to ground.
FIGURE 4. Voltage Noise Spectral Density vs Source
Resistance.
FIGURE 6. Pyroelectric Infrared Detector.
FIGURE 3. Connection of Input Guard.
NOISE: FET VERSUS BIPOLAR
Low noise circuit design requires careful analysis of all
noise sources. External noise sources can dominate in many
cases, so consider the effect of source resistance on overall
operational amplifier noise performance. At low source
impedances, the lower voltage noise of a bipolar operational
amplifier is superior, but at higher impedances the high
current noise of a bipolar amplifier becomes a serious
liability. Above about 15k
, the OPA111 will have a lower
total noise than an OP-27 (see Figure 4).
BIAS CURRENT CHANGE
VERSUS COMMON-MODE VOLTAGE
The input bias current of most popular BIFET operational
amplifiers are affected by common-mode voltage (Figure 5).
Higher input FET gate-to-drain voltage causes leakage and
ionization (bias) currents to increase. Due to its cascode
input stage, the extremely low bias current of the OPA111 is
not compromised by common-mode voltage.
APPLICATIONS CIRCUITS
Figures 6 through 18 are circuit diagrams of various appli-
cations for the OPA111.
FIGURE 5. Input Bias Currrent vs Common-Mode Voltage.
80
60
40
20
0
–20
–15
–10
–5
0
5
10
15
Common-Mode Voltage (VDC)
I
OPA111
AD547
LF156/157
LF155
T
= 25°C; curves taken from
manufacturers' published
typical data.
OP-15/16/17
"Perfect Bias Current Cancellation"
OPA111
2
3
6
Output
8
1000pF Polystyrene
1000M
1000M
Pyroelectric
Detector
NOTE: Pyroelectric
detectors respond
to rate-of-change
(AC signal) only.
3
2
4
5
6
7
8
1
OPA111
2
3
6
8
In
Out
Inverting
TO-99 Bottom View
OPA111
2
3
6
In
Out
Non-Inverting
8
OPA111
2
3
6
In
Out
Buffer
8
Board layout for input guarding: guard top and bottom of board.
Alternate: use Teflon
standoff for sensitive input pins.
Teflon
E. I. Du Pont de Nemours & Co.
100
1k
10k
100k
1M
10M
1k
100
10
1
V
O
H
T
BM
OP-27 + Resistor
OPA111 + Resistor
Resistor Noise Only
OPA111 + Resistor
Resistor Noise Only
OP-27 + Resistor
Source Resistance, R
S
(
)
E
O
R
S
E
O
= e
N2
+ (I
N
R
S
)
2
+ 4kTR
S
相關PDF資料
PDF描述
OPA111AM Low Noise Precision Difet OPERATIONAL AMPLIFIER
OPA111BM Low Noise Precision Difet OPERATIONAL AMPLIFIER
OPA111SM Low Noise Precision Difet OPERATIONAL AMPLIFIER
OPA121 Low Cost Precision Difet OPERATIONAL AMPLIFIER
OPA121KM Low Cost Precision Difet OPERATIONAL AMPLIFIER
相關代理商/技術參數
參數描述
OPA111AM 功能描述:運算放大器 - 運放 Low Noise Prec Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
OPA111AM 制造商:Texas Instruments 功能描述:OP AMP DIFET PRECISION TO-99 111
OPA111BM 功能描述:運算放大器 - 運放 Low Noise Precision Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
OPA111BM 制造商:Texas Instruments 功能描述:IC OP-AMP 2MHZ 2V/ TO-99-8 制造商:Texas Instruments 功能描述:IC, OP-AMP, 2MHZ, 2V/s, TO-99-8
OPA111SM 制造商:BB 制造商全稱:BB 功能描述:Low Noise Precision Difet OPERATIONAL AMPLIFIER