- 您現在的位置：買賣IC網 > PDF目錄376244 > OP470ATCMDA (ANALOG DEVICES INC) Very Low Noise Quad Operational Amplifier PDF資料下載
參數資料
| 型號： | OP470ATCMDA |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Very Low Noise Quad Operational Amplifier |
| 中文描述： | QUAD OP-AMP, 600 uV OFFSET-MAX, 6 MHz BAND WIDTH, CQCC28 |
| 封裝： | CERAMIC, LCC-28 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 658K |
| 代理商： | OP470ATCMDA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
REV. B
OP470
–11–
4. The test time to measure 0.1 Hz to 10 Hz noise should not ex-
ceed 10 seconds. As shown in the noise-tester frequency-response
curve of Figure 8, the 0.1 Hz corner is defined by only one pole.
The test time of 10 seconds acts as an additional pole to elimi-
nate noise contribution from the frequency band below 0.1 Hz.
5. A noise-voltage-density test is recommended when measuring
noise on a large number of units. A 10 Hz noise voltage-density
measurement will correlate well with a 0.1 Hz to 10 Hz
peak-to-peak noise reading, since both results are determined
by the white noise and the location of the 1/f corner frequency.
6. Power should be supplied to the test circuit by well bypassed
low noise supplies, e.g. batteries. These will minimize output
noise introduced via the amplifier supply pins.
FREQUENCY – Hz
100
0.01
G
80
60
40
20
0
0.1
1
10
100
Figure 8. 0.1 Hz to 10 Hz Peak-to-Peak Voltage Noise Test
Circuit Frequency Response
NOISE MEASUREMENT—NOISE VOLTAGE DENSITY
The circuit of Figure 9 shows a quick and reliable method of
measuring the noise voltage density of quad op amps. Each
individual amplifier is series-connected and is in unity-gain, save
the final amplifier which is in a noninverting gain of 101. Since
the ac noise voltages of each amplifier are uncorrelated, they
add in rms fashion to yield:
e
=101
e
+e
e
e
OUT
nA
nB
nC
nD
2
2
2
2
+
+
ê
ˉ
The OP470 is a monolithic device with four identical amplifiers.
The noise voltage density of each individual amplifier will match,
giving:
e
101
4e
= 101 2e
OUT
n
n
2
=
ê
ˉ
)
NOISE MEASUREMENT—CURRENT NOISE DENSITY
The test circuit shown in Figure 10 can be used to measure
current noise density. The formula relating the voltage output to
current noise density is:
i
G
40nV /
Hz
R
n
nOUT
S
=
ê
ˉ -
(
)
2
2
where:
G = gain of 10000
R
S
= 100 k
W
source resistance
R2
100k
R3
1.24k
OP470
DUT
R5
8.06k
OP27E
R4
200
e
n
OUT TO
SPECTRUM ANALYZER
R1
5
GAIN = 50,000
V
S
= 5V
Figure 10. Current Noise Density Test Circuit
R2
10k
1/4
OP470
1/4
OP470
1/4
OP470
1/4
OP470
R1
100
e
OUT
TO SPECTRUM ANALYZER
e
OUT
(nV Hz) = 101(2e
n
)
V
S
= 15V
Figure 9. Noise Voltage Density Test Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| OP470AYMDA | Very Low Noise Quad Operational Amplifier |
| OP470FY | Very Low Noise Quad Operational Amplifier |
| OP470 | Very Low Noise Quad Operational Amplifier |
| OP470AY | Very Low Noise Quad Operational Amplifier |
| OP470EY | Very Low Noise Quad Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP470AY | 制造商:Analog Devices 功能描述:OP470AY ((NS)) |
| OP-470AY | 制造商:AD 制造商全稱:Analog Devices 功能描述:VERY LOW NOISE QUAD OPERATIONAL AMPLIFIER |
| OP470AYMDA | 制造商:AD 制造商全稱:Analog Devices 功能描述:Very Low Noise Quad Operational Amplifier |
| OP-470E | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual/Quad Low Noise, Precision Operational Amplifiers |
| OP-470EJ | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual/Quad Low Noise, Precision Operational Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。