- 您現在的位置：買賣IC網 > PDF目錄299566 > OP262HRUZ (ANALOG DEVICES INC) 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: TSSOP 4.4 MM; No of Pins: 8; Temperature Range: Industrial PDF資料下載
參數資料
| 型號： | OP262HRUZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 運算放大器 |
| 英文描述： | 15 MHz Rail-to-Rail Operational Amplifier, Dual; Package: TSSOP 4.4 MM; No of Pins: 8; Temperature Range: Industrial |
| 中文描述： | DUAL OP-AMP, 1000 uV OFFSET-MAX, 15 MHz BAND WIDTH, PDSO8 |
| 封裝： | TSSOP-8 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 1235K |
| 代理商： | OP262HRUZ |
–13–
REV. D
OP162/OP262/OP462
The differential gain of the circuit is determined by RG, where:
ADIFF
= 1+
2
RG
with the RG resistor value in k
W. Removing RG will set the cir-
cuit gain to unity.
The fourth op amp, OP462-D, is optional and is used to im-
prove CMRR by reducing any input capacitance to the ampli-
fier. By shielding the input signal leads and driving the shield
with the common-mode voltage, input capacitance is eliminated
at common-mode voltages. This voltage is derived from the
midpoint of the outputs of OP462-A and OP462-B by using two
10 k
W resistors followed by OP462-D as a unity gain buffer.
It is important to use 1% or better tolerance components for the
2 k
W resistors, as the common-mode rejection is dependent on
their ratios being exact. A potentiometer should also be con-
nected in series with the OP462-C noninverting input resistor to
ground to optimize common-mode rejection.
The circuit in Figure 41 was implemented to test its settling
time. The instrumentation amp was powered with
±5V, so the
input step voltage went from –5 V to +4 V to keep the OP462
within its input range. Therefore, the 0.05% settling range is
when the output is within 4.5 mV. Figure 42 shows the positive
slope settling time to be 1.8
ms, and Figure 43 shows a settling
time of 3.9
ms for the negative slope.
10
0%
100
90
5mV
1 s
2V
Figure 42. Positive Slope Settling Time
10
0%
100
90
5mV
1s
2V
10
0%
100
90
5mV
1 s
Figure 43. Negative Slope Settling Time
Direct Access Arrangement
Figure 44 shows a schematic for a +5 V single supply transmit/
receive telephone line interface for 600
W transmission systems.
It allows full duplex transmission of signals on a transformer
coupled 600
W line. Amplifier A1 provides gain that can be
adjusted to meet the modem output drive requirements. Both
A1 and A2 are configured so as to apply the largest possible
differential signal to the transformer. The largest signal available
on a single +5 V supply is approximately 4.0 V p-p into a 600
W
transmission system. Amplifier A3 is configured as a difference
amplifier to extract the receive information from the transmis-
sion line for amplification by A4. A3 also prevents the transmit
signal from interfering with the receive signal. The gain of A4
can be adjusted in the same manner as A1’s to meet the modem’s
input signal requirements. Standard resistor values permit the
use of SIP (Single In-line Package) format resistor arrays. Couple
this with the OP462 14-lead SOIC or TSSOP package and this
circuit can offer a compact solution.
6.2V
TRANSMIT
TXA
RECEIVE
RXA
C1
0.1 F
R1
10k
R2
9.09k
2k
P1
TX GAIN
ADJUST
A1
A2
A3
A4
A1, A2 = 1/2 AD8532
A3, A4 = 1/2 AD8532
R3
360
1:1
T1
TO TELEPHONE
LINE
1
2
3
7
6
5
2
3
1
6
5
7
10 F
R7
10k
R8
10k
R5
10k
R6
10k
R9
10k
R14
14.3k
R10
10k
R11
10k
R12
10k
R13
10k
C2
0.1 F
P2
RX GAIN
ADJUST
2k
ZO
600
5V DC
MIDCOM
671-8005
Figure 44. A Single-Supply Direct Access Arrangement for
Modems
相關PDF資料 |
PDF描述 |
|---|---|
| OP27AJ/883C | Low Noise, Precision Operational Amplifier; Package: ROUND HEADER/METAL CAN; No of Pins: 8; Temperature Range: Military |
| OP27AZ/883C | Low Noise, Precision Operational Amplifier; Package: CERDIP GLASS SEAL; No of Pins: 8; Temperature Range: Military |
| OP27BJ/883C | Low Noise, Precision Operational Amplifier; Package: ROUND HEADER/METAL CAN; No of Pins: 8; Temperature Range: Military |
| OPT-1250A1I1H | RoHS Compliant 1X9 SC Duplex Receptacle Transceiver Module for Gigabit Ethernet |
| OPT-1250A1I1RAH | RoHS Compliant 1X9 SC Duplex Receptacle Transceiver Module for Gigabit Ethernet |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP262HRUZ | 制造商:Analog Devices 功能描述:IC, OP AMP, LOW NOISE, 15MHZ, 13V/s, TS |
| OP262HRUZ-REEL | 功能描述:IC OPAMP GP R-R 15MHZ LN 8TSSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:100 系列:- 放大器類型:通用 電路數:1 輸出類型:- 轉換速率:0.2 V/µs 增益帶寬積:- -3db帶寬:- 電流 - 輸入偏壓:100pA 電壓 - 輸入偏移:30µV 電流 - 電源:380µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):±2 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:管件 |
| OP262TRZ-EP | 功能描述:IC OPAMP GP R-R 15MHZ DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| OP262TRZ-EP-R7 | 功能描述:IC OPAMP GP R-R 15MHZ DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| OP265 | 制造商:OPTEK 制造商全稱:OPTEK 功能描述:GAAIAS PLASTIC INFRARED EMITTING DIODE |
發布緊急采購，3分鐘左右您將得到回復。