- 您現在的位置：買賣IC網 > PDF目錄5415 > OP2177AR-REEL (Analog Devices Inc)IC OPAMP GP 1.3MHZ DUAL LN 8SOIC PDF資料下載
參數資料
| 型號： | OP2177AR-REEL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP GP 1.3MHZ DUAL LN 8SOIC |
| 產品變化通告： | Product Discontinuance 27/Oct/2011 |
| 設計資源： | 16-Bit Fully Isolated Voltage Output Module Using AD5662, ADuM1401, and External Amplifiers (CN0063) |
| 標準包裝： | 2,500 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 轉換速率： | 0.7 V/µs |
| 增益帶寬積： | 1.3MHz |
| 電流 - 輸入偏壓： | 500pA |
| 電壓 - 輸入偏移： | 15µV |
| 電流 - 電源： | 400µA |
| 電流 - 輸出 / 通道： | 10mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 36 V，±2.5 V ~ 18 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 帶卷 (TR) |
OP1177/OP2177/OP4177
Rev. G | Page 15 of 24
(5V/DIV)
OPA277
VSY = ±15V
RL = 2k
(10
V
/DI
V
)
0
26
27
-0
52
Figure 52. Gain Linearity
INPUT OVERVOLTAGE PROTECTION
When input voltages exceed the positive or negative supply
voltage, most amplifiers require external resistors to protect
them from damage.
The OPx177 has internal protective circuitry that allows voltages as
high as 2.5 V beyond the supplies to be applied at the input of
either terminal without any harmful effects.
Use an additional resistor in series with the inputs if the voltage
exceeds the supplies by more than 2.5 V. The value of the resistor
can be determined from the formula
(
)
mA
5
500
≤
Ω
+
S
IN
R
V
With the OPx177 low input offset current of <1 nA maximum,
placing a 5 kΩ resistor in series with both inputs adds less than
5 μV to input offset voltage and has a negligible impact on the
overall noise performance of the circuit.
5 kΩ protects the inputs to more than 27 V beyond either supply.
Refer to the THD + Noise section for additional information on
noise vs. source resistance.
OUTPUT PHASE REVERSAL
Phase reversal is defined as a change of polarity in the amplifier
transfer function. Many operational amplifiers exhibit phase
reversal when the voltage applied to the input is greater than the
maximum common-mode voltage. In some instances, this can
cause permanent damage to the amplifier. In feedback loops, it
can result in system lockups or equipment damage. The OPx177
is immune to phase reversal problems even at input voltages
beyond the supplies.
VSY = 10V
AV = 1
TIME (400s/DIV)
VIN
VOUT
VOL
TA
G
E
(5
V/
D
IV)
02
62
7-
0
53
Figure 53. No Phase Reversal
SETTLING TIME
Settling time is defined as the time it takes an amplifier output
to reach and remain within a percentage of its final value after
application of an input pulse. It is especially important in measure-
ment and control circuits in which amplifiers buffer ADC inputs
or DAC outputs.
To minimize settling time in amplifier circuits, use proper
bypassing of power supplies and an appropriate choice of circuit
components. Resistors should be metal film types, because they
have less stray capacitance and inductance than their wire-wound
counterparts. Capacitors should be polystyrene or polycarbonate
types to minimize dielectric absorption.
The leads from the power supply should be kept as short as
possible to minimize capacitance and inductance. The OPx177
has a settling time of about 45 μs to 0.01% (1 mV) with a 10 V
step applied to the input in a noninverting unity gain.
OVERLOAD RECOVERY TIME
Overload recovery is defined as the time it takes the output
voltage of an amplifier to recover from a saturated condition to
its linear response region. A common example is one in which
the output voltage demanded by the transfer function of the
circuit lies beyond the maximum output voltage capability of
the amplifier. A 10 V input applied to an amplifier in a closed-
loop gain of 2 demands an output voltage of 20 V. This is beyond
the output voltage range of the OPx177 when operating at ±15 V
supplies and forces the output into saturation.
Recovery time is important in many applications, particularly
where the operational amplifier must amplify small signals in
the presence of large transient voltages.
相關PDF資料 |
PDF描述 |
|---|---|
| OP191GS-REEL7 | IC OPAMP GP R-R 3MHZ 16MA 8SOIC |
| OP191GS-REEL | IC OPAMP GP R-R 3MHZ 16MA 8SOIC |
| TSW-119-17-S-D | CONN HEADER 38POS .100" DL GOLD |
| MMA21-0071R1 | CONN RACK/PANEL 7POS 5A |
| TSW-120-17-S-D | CONN HEADER 40POS .100" DL GOLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OP2177AR-REEL7 | 功能描述:IC OPAMP GP 1.3MHZ DUAL LN 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| OP2177ARZ | 功能描述:IC OPAMP GP 1.3MHZ DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| OP2177ARZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers |
| OP2177ARZ-REEL | 功能描述:IC OPAMP GP 1.3MHZ DUAL LN 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| OP2177ARZ-REEL1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Precision Low Noise, Low Input Bias Current Operational Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。