參數資料
型號： NRF2402
廠商： Electronic Theatre Controls, Inc.
英文描述： Single chip 2.4 GHz Transmitter
中文描述： 2.4 GHz的單芯片發射機
文件頁數： 12/31頁
文件大?。?/td> 368K
代理商： NRF2402
PRODUCT SPECIFICATION
nRF2402/nRF2402G Single Chip 2.4 GHz Radio Transmitter
Nordic Semiconductor ASA -
Revision: 2.0
Vestre Rosten 81, N-7075 Tiller, Norway -
Page 12 of 31
Phone +4772898900
- Fax +4772898989
April 2005
Direct Mode
In direct mode the nRF2402/nRF2402G works like a traditional RF device. The data rate
must be 1Mbps ±200ppm, or 250kbps ±200ppm at low data rate setting, for the receiver
(nRF2402/nRF24E1) to detect the signals.
MCU interface pins: CE, DIN
1.
When application MCU has data to send, set CE high
2.
The nRF2402/nRF2402G RF front end is now immediately activated, and after
200
μ
s settling time, signal on the DIN pin will modulate the carrier directly.
3.
All RF protocol parts must hence be implemented in MCU firmware (preamble,
address and CRC).
Configuration Mode
In configuration mode a configuration word of up to 20 bits is downloaded to
nRF2402/nRF2402G. This is done through a simple 3-wire interface (CS, CLK and DIN).
For more information on configuration please refer to the nRF2402/nRF2402G device
configuration chapter, page13.
Power Down Mode
Power down mode is used to achieve very low current consumption. Effectively the chip is
disabled with minimal leakage current consumption, typically less than 200nA. Operating in
this mode when not transmitting data significantly increases battery lifetime.
Stand-By Mode
Stand by mode is used to achieve low current consumption. In this mode only a part of the
crystal oscillator is running (12
μ
A) to guarantee a short start-up time. Operating in this mode
when not transmitting data increases battery lifetime while keeping start up delays short.
Pin configuration for the different modes of nRF2402/nRF2402G
nRF2402/nRF2402G
MODES
Pin Name
PWR_UP CE
Power down
0
Stand by
1
Configuration
1
TX ShockBurst
1
TX Direct
1
INPUT PINS
CS
X
0
1
0
0
CLK
X
X
CLK
CLK
Set to 0
DIN
X
X
0
0
0
1
1
CONFIG DATA
TX DATA
TX DATA
Table 7 Pin configuration of nRF2402/nRF2402G.
CLK not used in direct mode.
相關PDF資料
PDF描述
NRF2402G Single chip 2.4 GHz Transmitter
NRF902 Single chip 868 MHz Transmitter
NRF9E5-EVKIT868 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC
NRF9E5-EVKIT433 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC
NRF9E5-EVKIT915 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC
相關代理商/技術參數
參數描述
nRF2402G 功能描述:射頻發射器 1.9-3.6V 1MBIT XMTR 2.4GHz SHCKBRST RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel
nRF2402G-REEL 功能描述:射頻發射器 1.9-3.6V 1MBIT XMTR 2.4GHz SHCKBRST RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel
nRF2402G-REEL7 功能描述:射頻發射器 1.9-3.6V 1MBIT XMTR 2.4GHz SHCKBRST RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel
NRF2402-REEL 制造商:Nordic Semiconductor 功能描述:
NRF2460-DK 功能描述:射頻開發工具 2.4 GHz ISM band 16 bit res RoHS:否 制造商:Taiyo Yuden 產品:Wireless Modules 類型:Wireless Audio 工具用于評估:WYSAAVDX7 頻率: 工作電源電壓:3.4 V to 5.5 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*