參數資料
型號： NRF2401AG
廠商： Electronic Theatre Controls, Inc.
英文描述： Single chip 2.4 GHz Transceiver
中文描述： 單片2.4GHz無線收發
文件頁數： 12/38頁
文件大小： 263K
代理商： NRF2401AG
PRODUCT SPECIFICATION
nRF2401A Single Chip 2.4 GHz Radio Transceiver
nRF2401A ShockBurst Receive:
MCU interface pins: CE, DR1, CLK1 and DATA (one RX channel receive)
1.
Correct address and size of payload of incoming RF packages are set when
nRF2401A is configured to ShockBurst RX.
2.
To activate RX, set CE high.
3.
After 200
μ
s settling, nRF2401A is monitoring the air for incoming
communication.
4.
When a valid package has been received (correct address and CRC found),
nRF2401A removes the preamble, address and CRC bits.
5.
nRF2401A then notifies (interrupts) the MCU by setting the DR1 pin high.
6.
MCU may (or may not) set the CE low to disable the RF front end (low
current mode).
7.
The MCU will clock out just the payload data at a suitable rate (ex. 10
kbps).
8.
When all payload data is retrieved nRF2401A sets DR1 low again, and is
ready for new incoming data package if CE is kept high during data
download. If the CE was set low, a new start up sequence can begin, see
Figure 16.
Nordic Semiconductor ASA - Vestre Rosten 81, N-7075 Tiller, Norway -
Revision: 1.0
Phone +4772898900
-
Fax +4772898989
December 2004
Page 12 of 38
Direct Mode
In direct mode the nRF2401A works like a traditional RF device. Data must be at
1Mbps ±200ppm, or 250kbps ±200ppm at low data rate setting, for the receiver to
detect the signals.
Direct Mode Transmit:
MCU interface pins: CE, DATA
1.
When application MCU has data to send, set CE high
2.
The nRF2401A RF front end is now immediately activated, and after 200
μ
s settling time, data will modulate the carrier directly.
3.
All RF protocol parts must hence be implemented in MCU firmware
(preamble, address and CRC).
Direct Mode Receive:
MCU interface pins: CE, CLK1, and DATA
1.
Once the nRF2401A is configured and powered up (CE high) in direct RX
mode, DATA will start to toggle due to noise present on the air.
2.
CLK1 will also start to toggle as nRF2401A is trying to lock on to the
incoming data stream.
3.
Once a valid preamble arrives, CLK1 and DATA will lock on to the
incoming signal and the RF package will appear at the DATA pin with the
same speed as it is transmitted.
4.
To enable the demodulator to re-generate the clock, the preamble must be
8 bits toggling hi-low, starting with low if the first data bit is low.
5.
In this mode no data ready (DR) signals is available. Address and
checksum verification must also be done in the receiving MCU.
相關PDF資料
PDF描述
NRF2402 Single chip 2.4 GHz Transmitter
NRF2402G Single chip 2.4 GHz Transmitter
NRF902 Single chip 868 MHz Transmitter
NRF9E5-EVKIT868 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC
NRF9E5-EVKIT433 433/868/915MHz RF Transceiver with Embedded 8051 Compatible Microcontroller and 4 Input, 10 Bit ADC
相關代理商/技術參數
參數描述
nRF2401AG-REEL 功能描述:射頻收發器 1.9-3.6V 1MBIT XCVR 2.4GHz SHCKBRST RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
nRF2401AG-REEL7 功能描述:射頻收發器 1.9-3.6V 1MBIT XCVR 2.4GHz SHCKBRST RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
NRF2401-AREEL 制造商:Nordic Semiconductor 功能描述:
NRF2401-EVKIT 制造商:Nordic Semiconductor 功能描述:2X BOARDS + 2 WHIP ANT. 2.4GHZ 制造商:Nordic Semiconductor 功能描述:EVALUATION KIT
NRF2401GA 制造商:Nordic Semiconductor 功能描述:IC TRANSCEIVER 2.4GHZ SMD 制造商:Nordic Semiconductor 功能描述:IC, TRANSCEIVER, 2.4GHZ, SMD
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*