- 您現在的位置：買賣IC網 > PDF目錄1958 > NM485DC (Murata Power Solutions Inc)ISOLATED INTERFACE EIA-485 DL PDF資料下載
參數資料
| 型號： | NM485DC |
| 廠商： | Murata Power Solutions Inc |
| 文件頁數： | 3/6頁 |
| 文件大?。?/td> | 0K |
| 描述： | ISOLATED INTERFACE EIA-485 DL |
| 標準包裝： | 15 |
| 系列： | IsoLoop® |
| 類型： | 收發器，隔離式 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS485 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.667"，16.95mm） |
| 供應商設備封裝： | 24-DIL |
| 包裝： | 管件 |
| 產品目錄頁面： | 2721 (CN2011-ZH PDF) |
| 其它名稱： | 811-1445-5 |
NM485DC Series
Isolated Dual EIA-485 Driver and Receiver
KII_NM485DC.A05 Page 3 of 6
www.murata-ps.com/support
APPLICATION NOTES
The EIA-485 standard is an upgrade version of the EIA RS-422 standard. The use of balanced data transmission lines in distributing data to several systems components
and peripherals over relatively long lines, requires the use of multiple driver/receiver combinations on a single twisted pair line. This is referred to as a party-line (see
gure 1).
The NM485DC is an isolated interface device providing EIA-485 compatibility. A single supply provides all necessary power for the device, either side of the isolation bound-
ary. The isolation feature allows the logic and differential grounds to be isolated from each other, eliminating ground loop current and inherently long noise paths.
The maximum number of drivers and receivers that may be placed on a single communication bus depends upon their loading characteristics, relative to the denition of
a Unit Load (U.L.), transmission speed does not affect the unit load capability. As the NM485DC complies with the EIA-485 standard a maximum of 32 unit loads per line is
recommended. A unit load usually consists of a driver-receiver pair, but not the line termination resistors.
With only a 5V supply connected, the NM485DC receiver and differential outputs give levels greater than +2.7V and ±1.5V respectively. This known output state may be
used as a reference for use in environments with considerable levels of noise. An unused driver should be disabled by grounding it’s enable pin to reduce power dissipation.
Figure 2 illustrates the way one receiver and one driver of the NM485DC may be connected to implement an isolated EIA-485 interface with a typical UART and processor
bus. Figure 3 demonstrates how the NM485DC may be used as a transceiver. This is possible by using the driver enable to determine the data direction. For example, the
device could receive when the driver enable is low and transmit when it is high.
Precise circuitry will depend on the application and in particular the use of the control lines shown will need to be altered to suit the situation. For instance the maximum
sychronous baud rate of the 8251A is 64kbps, whereas the NM485DC had a maximum baud rate of 1.25Mbps.
Implementing an isolated LONWORKS () network using the
NM485DC
The Echleon LONWORKS (Local Operating Network) network
is designed to be used in industrial applications in which other
eletrical equipment is operated. Often the LON (R) will be the
method of controlling machinery or sensing machine activity.
The environment is therefore likely to be electrically noisy and
to reduce the possibility of data corruption, an isolated network
communications system is a preferred method of data transfer.
The EIA-485 standard provides a method of achieving multi-
point (multi-drop) data transmission over balanced twisted
pair transmission lines. The standard is a differential scheme
offering a large degree of common mode immunity compared
to single ended schemes. The isolated differential method offers
the highest common mode and line noise immunity for wire
based systems.
The NM485DC is a fully isolated EIA-485 standard dual driver
and receiver, which requires only a single 5V supply. The
device offers full data direction programming and can hence be
congured as a transceiver. The NM485DC can be operated at
transmitting or receiving data rates of up to 1.25Mbps, hence
is fully compatible with the LONTALK () transmission rate
standards.
Conguring the NM485D as a transceiver
The NM485D is congured as a transceiver simply by con-
necting the inverting R1B receive to the inverting D1Z drive and
the non-inverting R1A receive to the non-inverting D1Y drive,
similarly R2B to D2Z and R2A to D2Y for the second transceiver
(see gure 3), in this way the NM485D is congured as a dual
transceiver. The data direction is determined by the driver en-
able pins (DX ENABLE), the transceiver acting as a transmitter
when the enable pin is high and a receiver when the enable pin
is low.
If only a single transceiver is required it is recommended that
the second transceiver driver is disabled, this reduces the power
consumption to around 0.6W. The second driver is disabled by
taking the driver enable pin low, this should be via a pull-down
resistor (recommend value is 1KΩ).
Figure 1
Figure 2
Figure 3
相關PDF資料 |
PDF描述 |
|---|---|
| NM485SLC | ISOLATED INTERFACE LP EIA-485 |
| NS3L500MTTWG | IC ETH LAN SW 2:1GB 8CH 56-WQFN |
| NS5A4684SMNTBG | IC ANLG SWITCH DUAL SPDT 10WQFN |
| NS5B1G384DFT2G | IC ANLG SWITCH SPST NC SC-70-5 |
| NS5B1G385DFT2G | IC ANLG SWITCH SPST NO SC-70-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NM485SLC | 功能描述:RS-485接口IC Iso Dual EIA-485 Driver and Receiver RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| NM4B | 制造商:Panduit Corp 功能描述:Cable Accessories 制造商:Panduit Corp 功能描述:NM4 AND NMF4 BLANKING KIT - Bulk |
| NM-4-F4 | 制造商:ESSENTRA COMPONENTS 功能描述:LOOP CLAMP W/EYELET NAT 1/4" 制造商:Richco 功能描述:LOOP CLAMP W/EYELET NAT 1/4" |
| NM4-KIT | 制造商:Panduit Corp 功能描述:KIT FOR NM4 制造商:Panduit Corp 功能描述:KIT FOR NM4 - Bulk |
| NM-4-R4 | 功能描述:LOOP CLAMP W/ EYELET GRN 1/4" RoHS:是 類別:線纜，導線 - 管理 >> 線夾和夾具 系列:NM-R 標準包裝:100 系列:TC 類型:C-夾 開口尺寸:0.79" L x 0.54" W x 0.67" H（20.1mm x 13.7mm x 17.0mm） 安裝類型:釘子 材質:聚丙烯 顏色:黑 |
發布緊急采購，3分鐘左右您將得到回復。